Niveland^® 10 CT C25 F5

Technical Caracteristics

Product based on cements,  selected aggregates and additives.

Advantages and Uses

• Irregular pavements levelling in interior areas.
• High mechanical resistance.
• Easy to apply
• High self-levelling capacity.
• Floors' smoothing in residential areas with moderate  pedestrian traffic, before placing the final pavement: ceramic, parquet, PVC, linoleum, etc.

Suitable Substrates

• Concrete, cementitious floorings or substrates  with a suitable resistance or similar stregth.  In case of working with other substrates, please consult our technical department.
• Substrates must be resistant, stable,  sound, and clean, free from dust or any other kind of substances, organic products, etc.
• If necessary prepare the substrate mechanically so that the surface if free from grout and has the appropriate porosity.
• Before applying NIVELAND 10, any possible hollows and cracks should be adequately repaired using the PAVILAND or MORCEMREST adequate product, according to the nature of the substrate and the type of reparation  required.
• Apply Paviland Primer R to avoid the formation of air bubbles in the cladding and in order to improve its adherence to the substrate according to the instructions given in the technical data sheet of the product.
• Before applying the paste, ensure that the residual humidity is below the recommended level (lower than 3%).

Application Procedure

• Mix the product with water (5.00-5.25 L per each 25 Kg bag), with a mechanic mixer at low speed (500 rpm approximately) until getting a homogeneous paste without lumps. It is essential to add the exact specified amount of water in order to avoid the segregation of the product, high retractions and a decrease in  resistance.
• Let the mixture stand for 2 minutes and remix.
• The paste should be used during the following 30 minutes after it has been prepared, this, of course, will depend on environmental conditions as well.
• Pour the mixed product on top of the substrate and spread it with a levelling trowel.
• The maximum thickness suggested would be around 10mm thickness applying it in just one layer.
• Respect the structural joints and carry out perimeter and partition joints.
• NIVELAND 10 must be protected, as it is not an appropriate material to remain uncovered.

Recommendations

• Do not apply it under 5ºC nor above 30ºC.
• Do not apply when there is a risk of frost, strong wind or direct sun weather conditions
• Not recommended for exterior use Do not apply  on floors with humidity or that may suffer from it in the future.
• Do not add any  aggregates, cement nor any type of product that may modify the original formula.
• Once the product has been mixed and its resting time has passed, do not add any more water.
• For floors larger than 20 m2 or longer than 10 lineal metres, it is advisable to make partitioning joints, delimiting panels with 6 mm joints that can be sealed with PUMALASTIC MS or PU.
• Movement joints on the original substrate must be respected and permiteral joints made.
• The surface coat should be protected against an extremely fast drying, specially under high temperatures or heavy winds conditions.
• Before placing the final pavement, you should check the residual humidity of the floor and confirm it is adequate for the type of flooring to be installed.

Packaging and Storage

25kg laminated paper bags.
1 year storage in its original packaging, away from extreme weather conditions and humidity.

Technical data

(Statistic results were obtained under standard conditions).

CE Mark

GRUPO PUMA SL Avda. AGRUPACIÓN CÓRDOBA, 17 14014 CÓRDOBA 18 Nº:501870-01
EN 13813 NIVELAND 10 Self-levelling mortar (CT.C25-F5 type) for indoor floors preparation, installation of  light floorings such as tiles, parquet, fitted carpet, etc. Thickness from 2 mm to 10 mm.
Fire reaction	Clase A1
Emission of harmful substances	CT
Compressive Strength Flexural Strength	C25 F6
Dangerous substances	Check Safety Data sheet

Legal Disclaimer