Pumaplast®
Powder filler for plastering, to smooth out, fill in cracks, scrapes, holes, etc., ideal for plastering plasticized Gotele surfaces.
Additional information
Technical Caracteristics
Mineral charges and water soluble polymers.
Advantages and Uses
- For general use in interiors on supports such as plaster, plasterboard, mortar, concrete, and old paint, etc.
- To smooth and level plasticized Gotele.
- Filler for small defects, holes, scrapes, cracks, and crevices, etc.
- Smooth, hard, and white finish, suitable to apply on any type of plastic paint or painted paper, etc.
- Easy preparation and application with trowel or scraper.
- Quick and easy sanding.
- Reduces the absorption of supports, increasing the yield of the paint.
- Good tackiness.
Suitable Substrates
- The supports should be free of dust, grease, wax, etc.
- Poorly adhered paint that remains should be removed.
- Very absorbent supports must be previously treated with a fixative or sealer.
- Do not apply on supports when frozen, very hot, wet, or if it has elevated levels of humidity.
Application Procedure
- Mix 1Kg of the product with 0.5 litres of water and slowly add small doses of water until an ideal working point is achieved, and attain a homogeneous and consistent paste.
- Mix manually or with mixing machine that does not go above 500 rmp.
- Apply with stainless steal trowel or scraper.
- Immediately after use clean tools with water.
Recommendations
- Do not apply at temperatures below 5ºC nor above 35ºC.
- Do not apply in humid environments that are constantly higher than 85%.
- Do not apply if there's a risk of frost.
Packaging and Storage
15 Kg plastic-lined paper bags and polyethylene packs of 5 Kg.
Storage up to 12 months in its original closed container, sheltered from weather and moisture.
Technical data
(Statistical data obtained under standard conditions)
| Aspect | WHITE powder |
| Solvent | Water |
| Apparent density of powder | Aprox. 0,700 g/cm³ |
| Apparent density of paste | Aprox. 1,400 g/cm³ |
| Grains seize distribution | < 200 µm |
| pH | 7 ± 0.5 |
| Adheres to plaster | > 0.5 N/mm² |
| Shore C hardness | > 75 |
| Maximum thickness per layer | 5 mm. |
| Mix shelf life | > 6 hours at 20ºC |
| Approximate Yield | Aprox. 1.5 m²/Kg per mm of thickness |
| Dry | 3-4 hours per mm applied (variants depending on environmental conditions and supports) |
| Sanding/painting | After it is dry |
Legal Disclaimer
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.