Paviland^® Sport AC Base

Technical Caracteristics

Watery acrylic resin with mineral loads.

Advantages and Uses

• Colour range. 
• Easy to apply.
• Compensation of irregularities.
• Anti-slip.
• Water-based product without solvents.
• Interior / Exterior.
• Sports flooring 
• Bicycle lanes.
• Hard shoulders, traffic islands, markings, sidewalks, etc.
• Suitable for interior garages, or low-traffic exterior car park areas.
• Adhesion and levelling layer on asphalt substrates for the Paviland Sport AC and EPW systems.
• Levelling layer on concrete substrates for the Paviland Sport AC systems.

Suitable Substrates

• Concrete with adequate strength, open pore, and slight roughness.
• Substrates must be resistant enough, stable, sound, and clean. Free of dust, release agents, organic products, etc.
• Concrete substrates: PAVILAND SPORT EPW PRIMER must be applied beforehand (consult the corresponding technical data sheet for concrete evaluation).
• Asphalt substrates: They must be resistant, stable, sound, and clean, free of dust, release agents, organic residues, etc. Before application, any voids and/or cracks in the substrate should be properly repaired using products from the PAVILAND ASFALTO range.

Application Procedure

• This product is ready to use. It should be previously homogenised with a corresponding mixer, at low speed for two minutes approximately.
• Pour the product onto the substrate and spread it with a rubber rake, starting from one corner and continuing linearly from end to end, paying special attention to specific points (junctions with vertical surfaces, etc.).    

Recommendations

• Do not apply the product under temperatures of 10º nor above 30º.
• Do not apply under the risk of frost, rain, heavy wind, or direct sun light.
• Use gloves and protective goggles when manipulating the product. In case of direct eye contact, clean them with abundant water and soap and visit a specialist.
• In case of direct skin contact, clean the area with water before it dries.
• Keep away from children.
• Any equipment and tools will be cleaned with water immediately after being used.
• Once the product gets hard, it will only be removed by mechanical means.
• Do not eat or smoke when manipulating the product.
• Empty containers should be removed or thrown according to the current legislation.

Packaging and Storage

Colour range

Technical data

(Statistical results obtained under standard conditions).

Time of application

Timings are given according to temperatures of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures.

Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.

Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.