Paviland^® Poliaspártica

Advantages and Uses

• High mechanical and chemical resistance.
• It practically does not turn yellow.
• Suitable for interior and exterior use.
• Excellent adhesion.
• High-coverage resin.
• Applicable on pedestrian floors indoors and outdoors on cementitious substrates. UV-resistant.
• Easy to apply ready to use with good spreadability. 
• Fast put into use.

Suitable Substrates

• Concrete with suitable resistance (25N/mm² minimum compressive strength and 1,5 N/mm² resistance to traction) open porous and light roughness.
• Substrates must be resistant enough, stable, healthy, and clean. Free of dust, release agents, organic products, etc.
• Before applying any product make sure all holes and / or cracks are previously repaired on the substrate by using products from our PAVILAND or MORCEMREST range.
• It is also advisable to conduct a milling or sanding process of the substrate with the main objective or opening the porous and remove any possible adhered materials such as greases, paints, etc.
• Apply the appropriate primer beforehand, according to the chosen construction system and the substrate’s porosity and maximum moisture level.
• For application on other substrates not covered in this technical data sheet, please consult our technical department.

Timings are given according to temperatures of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures

Application Procedure

• Homogenise component A. Pour component B on top of component A and mix them with a suitable mixer at low speed, until getting a homogeneous product.
• The pot life of the mixture is short, between 15 and 20 minutes depending on ambient temperature.
• Apply using a notched or flat metal trowel, rubber rake, or short-pile roller, depending on the desired finish and thickness.
• Subsequent layers may be added at intervals of 40–60 minutes, depending on temperature, ambient humidity, and thickness.

Recommendations

• Do not apply below 5º or above 35º, and avoid application in conditions at risk of frost, intense winds, or direct sunlight.
• Rain-resistant from 2 hours after application.
• Use gloves and protective goggles when manipulating the product. In case of direct skin or clothes contact, clean the area with abundant water and soap.
• Keep away from children.
•  Do not add any water to the mixture.
• The allowable substrate moisture will depend on the chosen primer, but as a general rule, it should be dry.
• Any equipment and tools will be cleaned with solvent immediately after being used.
• Once the product gets hard, it will only be removed by mechanical means.
• Do not eat or smoke when manipulating the product.
• Empty containers should be removed or thrown according to the current legislation.
   

Packaging and Storage

20 Kg containers (Component A 15 + Component B: 5) and 5 Kg (component A: 3.75 + Component B: 1.25)
Store the product up to 1 year in its closed original package, in cool and dry places, away from direct sun light and under 10-30ºC temperature.

Colour range

RAL: 3013, 3020, 6001, 6018, 7001 y 7037.Check availability for other colours

Technical data

(Statistic results obtained under standard conditions 23ºC)

Time of application

Timings are given according to temperatures of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures.

Legal Disclaimer

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.