Paviland^® Sport EPW Top

Technical Characteristics

Watery acrylic resin with mineral loads.

Advantages and Uses

• Wide range of colours.
• Easy to apply.
• Water based product.
• Indoors and outdoors.
• Sport areas pavements subjected to intense use. High-durability bike lanes.
• Suitable for indoor garages or low-traffic outdoor car park areas.
•  Finish coat for PAVILAND SPORT EPW Systems.
•  It is resistant to hydrocarbon spills. 

Suitable Substrates

• Substrates must be resistant enough, stable, sound and clean. Free of dust, release agents, organic products, etc.
• Direct application on concrete or cementitious substrates, must have the appropriate strength, open pores, and slight roughness. Before applying any product make sure all holes and / or cracks are previously repaired on the substrate by using products from our PAVILAND or MORCEMREST range. It is also advisable to conduct a milling or sanding process of the substrate with the main objective of opening the porous and removing any possible adhered materials such as greases, paints, etc. Residual humidity must not exceed 4%.
• Direct application on asphalt substrates: they must have the appropriate strength, open pores, and slight roughness. Before applying any product make sure all holes and / or cracks are previously repaired on the substrate by using products from our PAVILAND ASFALTO range. It is also advisable to conduct a milling or sanding process of the substrate with the main objective of opening the porous and removing any possible adhered materials such as greases, paints, etc. Residual humidity must not exceed 4%.
• Sealing of concrete substrates: PAVILAND SPORT EPW PRIMER must be applied beforehand (consult the corresponding technical data sheet for concrete evaluation).
• Finishing layer for High-Performance Sports Systems on concrete substrates: PAVILAND SPORT EPW PRIMER must be applied beforehand (consult the corresponding technical data sheet for concrete evaluation) as well as the intermediate PAVILAND SPORT EPW ACABADO coat, which must be dry.
• Finishing layer for High-Performance Sports Systems on asphalt substrates: PAVILAND SPORT AC BASE levelling coat must be applied beforehand (consult the corresponding technical data sheet for asphalt substrate evaluation) as well as the intermediate PAVILAND SPORT EPW ACABADO coat, which must be dry.
   

Application Procedure

• Thoroughly mix components A and B separately.
• Pour component B on top of component A and mix them with a suitable mixer at low speed, until getting a homogeneous product.
• It is recommended to apply a first coat diluted with 10% by weight of water on open-pore concrete or asphalt substrates. Then apply two additional coats without dilution.
• Apply a layer of the undiluted product on top of the previous PAVILAND SPORT range layers.
• Apply the product using an airless gun or paint brush.
• Approximately 2 hours later, only if the first coat is completely dry, a second coat can be applied.
   

Recommendations

• Do not apply the product under temperatures of 10º nor above 30º.
• Do not apply under the risk of frost, rain, heavy wind, or direct sun light.
• Use gloves and protective goggles when manipulating the product. In case of direct eye contact, clean them with abundant water and soap and visit a specialist.
• In case of direct skin contact, clean the area with water before it dries. 
• Keep away from children.
• Any equipment and tools will be cleaned with water immediately after being used. Once the product gets hard, it will only be removed by mechanical means.
• Do not eat or smoke when manipulating the product.
• Empty containers should be removed or thrown according to the current legislation.
   

Packaging and Storage

Colour range

 Albero, blue, white, grey, black, red, and green.

Technical data

(Statistical results obtained under standard conditions).

Timings are given according to temperatures of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures. 

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.