2. Products
  3. EIFS/ETICS
  4. Traditerm® Taco de Anclaje STR U 2G

Traditerm® Taco de Anclaje STR U 2G

Traditerm® Taco de Anclaje STR U 2G

Anchor fixings with threaded screw, for fixing TRADITERM® external insulation panels. High quality, secure anchor fixings. As it is a pre-assembled screw, it is easy and quick to install. It ensures a high quality fixing of the insulating panels to the support. With European Certification. Possibility of hidden anchorage in the system. Range of sizes, depending on the thickness of the panel. Use category according to ETA.

Download technical data sheet

Additional information

Technical Caracteristics

Polyethylene anchor fixings with steel screws.

Advantages and Uses

  • Easy and quick to use. Pre-assembled screw.
  • Ensures high quality fastening of insulation panels to the substrate.
  • Anchor fixings with European Certification.
  • Possibility of concealed anchoring in the system.
  • Fixing insulation panels in external thermal insulation system Traditerm®(EWI/ETICS). 
  • ETA usage category: A=Concrete / B=Solid Brick / C=Perforated/Hollow Brick, D =Lightweight Concrete / E=Aerated Concrete.
  • Range of sizes according to thickness of insulation panel.
 

Application Procedure

24 hours after fixing the insulation panels to the substrate with Traditerm® adhesive, drill a hole in the surface of the substrate going through the insulation panel. The drill bit should be 8 mm diameter.

Use the drill in rotary mode, except when the substrate is concrete or solid brick, in which case use it in hammer mode.

There are two methods of installing Traditerm STR U 2G Fixing Anchors:

• Interior Insulation Method.
Place the fixing anchor over the hole and turn towards the inside with the aid of the “Traditerm STR Capping Kit”.
Once the insulation fixing has been inserted, position the corresponding “Traditerm Insulation Cap” according to the insulation type.
 
• Surface Method.
Position the fixing anchor over the drilled hole and turn so that it penetrates the surface of the insulation panel by 1-2 mm.
Next, position the "Traditerm® STR Plug" and level the surface with Traditerm® mortar.
 

Recommendations

  • The fixing should be inserted at least 25 mm into the substrate Categories A, B, C and D and 65 mm inside substrate Category E.
  • The anchor should be cut 1 mm into the insulation panel in the case of the Surface Method. If the anchor is not inserted into the insulation panel, it will be visible in the final finish.
  • Check that the anchors are well secured.
  • The following STR U 2G fixing anchors are recommended, according to the thickness of the insulation panel:
Type of anchorage Thickness of TRADITERM panel (mm) Anchor block length (10 mm thick adhesive mortar layer + 20 mm thick existing plaster layer) Minimum number of anchors / m2 (Typical situations) Approval of anchor plug
Supports type A,B,C y D Supports type E
Traditerm Taco Anclaje STRU 2G  60 115 (surface method only) 115 (surface method only) 6 ETA-04/0023
70 135 175
80 135 175
90 155 195
100 155 195
120 175 215
140 195 235
150 215 255
160 215 255
180 235 275
200 255 295

Packaging and Storage

The fixing anchors are supplied in boxes of 100 units.
Store fixing anchors away from extreme weather conditions and sunlight.

Technical data

(Results obtained in laboratory under standard conditions)

Pre-drill diameter 8 mm
Washer diameter 60 mm
Depth of anchor in substrate 25 mm for substrate Categories A, B, C and D; 65 mm for substrate Category E
Approval  European 
Thermal Conductivity 0.002 W/mK
ETA usage category A=Concrete / B=Solid Brick / C=Perforated/Hollow Brick, D =Lightweight Concrete / E=Aerated Concrete
Performance Minimum 6 units/m2

 

Legal Disclaimer

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.