Pegoland^® Dos Porcelánico C2 TE

Technical Caracteristics

High-resistance cement-based product, with selected aggregates, additives and synthetic resins that guarantee high bond strength, excellent workability, and resistance to ageing.

Advantages and Uses

• Excellent initial adhesion.
• Due to its water retention power, there is no need to moisten the substrate.
• Adhesion of all types of ceramic pieces, porcelain stoneware, marble, granite, and natural stone.
• For interior application, exterior floors, and plinths.
• Swimming pool renders.
• Suitable for intense traffic pavements.
• Suitable for the installation of ceramic tiles on exterior plinths, if it complies with the specifications set out in standard UNE 138002.

Suitable Substrates

• Conventional cement-base substrates.
• Suitable for all type of drywall partitions (PYL type).
• Overlays on marble, granite, terrazzo, natural stone, and all types of ceramic substrates for interior floors and walls.
• Do not apply on top of paint.
• Substrates must be resistant enough, stable, sound  and clean. Free of dust, release agents, organic products, etc.
• All substrates should have adequate flatness. If this is not the case, make screeds of up to 5 mm with the same product 48 hours before gluing. For a greater thickness apply:
  • On bonded screeds: Apply levelling paste NIVELAND 10R or PAVILAND RECRECIDO AUTONIVELANTE depending on the substrate and requirements.
  • On flooring: Use regularization mortars with adequate tensile strength and with a curing shrinkage already completed.
• In case of heavy heat, wind, or very absorbent substrates, it is advisable to moisten the substrate and wait until the water film is totally absorbed.
• In exterior floors, the substrate must have a slope equal or greater than 1%.
• Do not apply on top of gypsum, plaster, anhydrite, or any other substrates with high content of sulphates, or in contact with water or moisten with high content of sulphates.
• All substrates must comply with the specifications outlined in section 6.4 of UNE 138002 standard.

Application Procedure

• Add water and mix manually or mechanically until getting a homogeneous consistence, easy to work with.
• Let the paste rest around 5 min. then mix again.
• Spread the kneaded product on the substrate with the help of a trowel on a maximum extension of 2m². 
• Comb the area with a notched trowel to level the thickness (check table).
• Place the tiles on the fresh adhesive, pressing and moving them until getting a complete smashing of the grooves and the proper adhesion of all the ceramic surface. Periodically check the stickiness of the adhesive by lifting a previously laid tile, if the appearance of a film without transfer on the surface of the adhesive or dehydration of the adhesive is observed, proceed to remove the material and apply a new product.
• Laying of tiles by back buttering method outdoors, for tiles with sides larger than 45 cm, in commercial or industrial flooring, when levelling systems are used, or if the tiles have a relief that hinders proper adhesive contact.
• Respect the placement joints between tiles as indicated in section 7.7 of UNE 138002 standard. For interior and pool areas, the joint width should be ≥ (1.5 - 3) mm, and for exterior areas, the joint width should be ≥ (3 - 5) mm, depending on the type of installation and the larger side of the tile being placed.Joints should be refilled after 24 hours in vertical parameters and 48 hours after in pavements
• Use a suitable MORCEMCOLOR range mortar taking into account the type of joint.

NOTE: The shorter the time between combing and laying the tile, the better results will be obtained.

Notched-trowel panel

Maximum tiles weight in vertical parameters: 40 kg/m² 

Recommendations

• The duration of the ceramic installation can only be ensured through careful planning. Therefore, we recommend consulting the current national standards in each country, such as the UNE 138002 standard in Spain, which provides specifications for material selection, proper planning, use, and installation, to achieve the required levels of quality, performance, and durability.
• Do not apply in temperatures below 5ºC or above 35ºC, and avoid application in conditions at risk of frost, rain, intense winds, or direct sunlight. Under extreme weather conditions (high wind or elevated temperatures) drying occurs faster.
• Temperatures, ventilation, absorption of the substrate and coating materials can vary the workability and setting times of the adhesive.
• Never apply with the “by dots” technique.
• Respect movement joints (structural, contraction, expansion, and perimeter joints) as indicated in section 7.8 of the UNE 138002 standard. These joints can be addressed by using prefabricated joints or filling them with an elastic sealant from the PUMALASTIC range.

Dimensioning of expansion joints 

Sizing of perimeter joints

• In applications on drywalls, make sure the substrate is well fixed to prevent movement.
• Remove any spare or bad adhered pieces in ceramic pavements and fill the gaps with mortar one day before the actual application of the product. Make sure the old ceramic is free from greases or waxes, if necessary, mill the surface until the old pottery loses its shine. In case of doubt, conduct a preliminary test to establish the suitability of the solution provided.
• Swimming pools can be refilled 7 days after applying the adhesive. The water tightness of the pool must be ensured by the construction of the pool itself.
• Use a PEGOLAND PROFESIONAL range adhesive for gypsum-based substrates, avoid old gypsum or weak plaster.
• Use PEGOLAND FLEX RECORD or PEGOLAND PROFESIONAL ELITE for slate.
• For pieces with fibreglass mesh reinforcement glued on the back, consult technical department.
• Pieces that can get stained due to their high-water absorption must be placed with fast-setting adhesives. Use PEGOLAND FAST FLEX C2FTE S1.

Packaging and Storage

25 kg plastic-lined paper bags.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.
Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.