Paviland^® Top EPW

Technical Characteristics

Two-component water-based epoxy sealing render.

Advantages and Uses

• The product exhibits exceptional adhesion to the substrate, even on damp surfaces.
• Easy to apply.
• Odourless.
• Surface hardener of the substrate.
• Permeable to water vapour and resistant to numerous aggressive agents.
• Tools must be cleaned with water.
• Dust-repelling effect.
• Garages.
• Warehouses.
• Chemical industry.
• Hygienic cleaning: easy-to-clean non-porous surfaces.

Suitable Substrates

• Concrete or cementitious self-levelling compound of suitable strength (minimum compressive strength of 25 N/mm² and tensile strength of 1.5 N/mm²), open-pored and slightly rough. Please consult our technical department for a different type of substrate.
• Substrates must be resistant enough, stable, sound, and clean. Free of dust, release agents, organic products, etc.
• Before applying any product make sure all holes and / or cracks are previously repaired on the substrate by using products from our PAVILAND or MORCEMREST range.
• It is also advisable to conduct a milling or sanding process of the substrate with the main objective or opening the porous and remove any possible adhered materials such as greases, paints, etc.
• The maximum allowable residual moisture content of the substrate must be less than 6%.
   

Application Procedure

• Thoroughly mix components A and B separately.
• Pour component B on top of component A and mix them with a suitable mixer at low speed, until getting a homogeneous product.
• Apply a first coat using a brush, short-haired roller, or airless method. This coat can be diluted (10-15%) with water to be used as a primer.
• The second coat, undiluted, is applied within the timeframes indicated in the schedule available at the end of this technical data sheet. Please note that these timeframes are approximate and depend on environmental features.
• Finish must be smooth and uniform. Uneven application or different thicknesses of the product might cause variations in the floor's colour tone.
• Protect the flooring for at least 48 hours following its application. 

Recommendations

• Do not apply the product under 10ºC due to the potential resin crystallization.
• Do not apply it above 30ºC.
• Do not apply under the risk of frost, rain, heavy wind, or direct sun light.
• The product will change colour or may experience discolouration when used outdoors or exposed to UV radiation; hence, it is recommended for indoor use only.
• Use gloves and protective goggles when manipulating the product. In case of direct skin or clothes contact, clean the area with abundant water.
• Keep away from children.
• The substrate should not be waterlogged. The maximum moisture content should be 6%.
• Low temperatures or intervals exceeding 48 hours between coats can cause coverage issues between renders.
• Excessive thickness in its application may cause differences in shine and/or cloudiness in the final appearance of the pavement.
• Any equipment and tools will be cleaned with water immediately after being used. Once the product gets hard, it will only be removed by mechanical means.
• Do not eat or smoke when manipulating the product.
• Empty containers should be removed or thrown according to the current legislation.
• As a consequence of the change in raw materials, the shades of the coloured mortars may vary slightly by batch.
   

Packaging and Storage

Colour range

Technical data

(Statistical results obtained under standard conditions).

Time of application 

Timings are given according to temperatures of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures.

Environmental Product Declaration (EPD)

This mortar has been elaborated with arid located close to our production centres, which has, reduce the emission of greenhouse effect gases thanks to transport and ISO 14001 certified production centres with environmental management, with a firm commitment to sustainability and respect for the environment.
Type III eco-friendly labelled mortar (The strictest one) verified  Environmental Product Declaration by AENOR
 

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.