Pegoland® Profesional Porcelánico C2 TE

Cementitious adhesive made of mixed binders with an excellent workability, pure whiteness and high adherence. Non slip  and extended open time. Suitable for interior and exterior pavements, interior claddings and baseboards. Suitable for overlaying new pavements on top of a previous tiled floor and underfloor  heating flooring. Suitable for the placing  for all kind of ceramic pieces, porcelain clay, natural stone, granite and marble. Suitable for plaster substrates and anhydrite.

TECNO ADAPT 12004 - C2 TE COV GBC Casita_Piscina

Download technical data sheet


Additional information

Composition

Product based on high resistance cement, selected additives and synthetic resins  that provide a an excellent grip strength, workability and  resistance to ageing.

Features and applications

  • Excellent  workability and pure whiteness.
  • Improved to provide high stability and an excellent performance.
  • Creamy thixotropic material.
  • Technologically advanced, compatible with a a large variety of substrates.
  • Stable in a wide range of mixing methods. High thixotropic efficiency,  improved convenience and lesser effort. Due to its water retention power, there is no need to wet the substrates or pieces beforehand. 
  • Non slip. Excellent initial adherence.
  • Extended open time, it allows the correction of the parts involved.
  • High humectant capacity .
  • Up to 15 mm application thickness, without sagging.
  • All kind of ceramic pieces adhesion (double or single fired ceramic, clinker, etc.), porcelain clay, marble, granite and natural stone.
  • Exterior and interior application.
  • Compatible with underfloor radiant flooring and overlaying in interior. Swimming pools' cladding.
  • Suitable for pavements with intense traffic.
  • Suitable for up to 40 x 40 cm pieces in exterior claddings, and up to 3 m high.

Substrates

  • Conventional substrates based on cement, plaster, or anhydrite without a primer being required.  
  • Suitable for fixing works on all types of plasterboard drywalls, large format clay brick, concrete, aerated concrete, fibre-cement, plaster based bricks or mortars and self-levelling pastes.
  • Floor coverings such as marble, granite, terrazzo, natural stone and all types of tiles.
  • Do not apply on painted surfacesSubstrates must be resistant, stable, sound and clean, free of dust, demolding agents, organic products, etc.
  • All substrates must have the appropriate flatness (maximum deviation tolerance of ±3 mm measured under a 2 metre ruler).  If it is not the case, smooth down up to 5 mm with the same product 48 hours prior to bonding.  If a higher thickness is required the following is recommended:
    •  On screeds: use NIVELAND 10R or  PAVILAND RECRECIDO AUTONIVELANTE, according to the substrate and requirements.
    •  On claddings: use  cladding mortars with adequate tensile strength with drying shrinkage already completed.
  • In case of hot or windy weather conditions or when applying over absorbent substrates, it is advisable to wet the substrate and wait until the thin layer of water disappears.
  • On outdoor flooring, substrates must have a gradient equal or superior to 1%.

Instructions for use

  • Add water and mix it manually or mechanically until obtaining a homogeneous and workable consistency. Let the mixture stand for 7 minutes and remix it. 
  • Spread the mixed product onto the substrate  with a  trowel covering to a maximum surface area of  2m2.
  • Periodically check the stickiness of the adhesive by lifting a previously placed tile. If you can see a film without transfer on the surface of the adhesive or the drying of the adhesive, remove the material and re-apply the product.
  • Spread with a notched trowel to adjust the thickness (see chart).Lay the tiles, pressing and  make small rotation movements  to ensure total and correct adhesion to the ridges and correct adhesion with the entire surface.
  • For formats above 900 cm2 or for exteriors, it is recommendable to use the double bond method. 
  • Respect the construction joints (expansion, contraction, sealing, corner joints) and placing between bricks (minimum 2 mm inside and 5 mm outside).
  • Joints can be sealed after 24 hours  in vertical parameters and 48 hours in pavements. Use a suitable mortar from the MORCEMCOLOR RANGE, according to the type of joint.


NOTE: For better results lay tiles as soon as possible after spreading  the product.
 

Cautions and recommendations

  • Do not apply  the product under extreme weather conditions.
  • Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
  • Do not use the technique known as by globs.
  • Temperatures, ventilation, absorption of the substrates and covering materials may vary the workability and drying timings of the adhesive.
  • Under extreme weather conditions (heavy winds or very high temperatures) the adhesive will experience a quicker drying process.
  • On flooring and facings with a surface area greater than 50 m2 for interiors, and 30 m2 for exteriors, or for elongated areas over 15 lineal metres, it is recommended to leave separation or sealing joints filled with a deformable material (Pumalastic-PU).
  • It is advisable to keep a free perimeter expansion joint between the floor and the wall or pillar, hidden by a baseboard (of approximately 5 mm). These joints should be sealed with a deformable material (we recommend the use of PUMALASTIC RANGE of products)
  • On floorings with underfloor heating, apply when substrate is at room temperature (between 5ºC and 30ºC).
  • Underfloor heating systems should be switched off at least 48 hours prior to use and should be switched back on again gradually at least 7 days after installing the flooring and pointing operation.
  • Swimming pools can be refilled 7 days after applying the adhesive.
  • The water-tightness of a swimming pool must be ensured before using the product on it.
  • When using  it on plasterboard, ensure the substrate is fixed well to avoid any movement.
  • Anhydrite screeds must be perfectly dry (Maximum residual humidity: 0,5%), hard enough and free from dust or superficial grout which, in this case, should be removed by sanding the area.
  • On top of ceramic pavements (tiles overlaying ), remove badly adhered pieces and fill the gaps with mortar the day before the fixing work is performed.
  • Ensure that the old ceramic is free of traces of fats or waxes, if necessary proceed to the milling of the enameled surface until the loss of brightness of the old ceramic. In case of doubt, make a preliminary test to establish the suitability of the solution provided..
  • When dealing with slate, use  PEGOLAND FLEX RECORD or PEGOLAND PROFESIONAL FLEX ELITE.
  • For elements reinforced with fibreglass meshing on the back, please consult our technical department.
  • Pieces that may get stains due to their high water absorption should be placed using fast drying adhesives. Use  PEGOLAND FAST FLEX C2FTE S1.

Packaging

20 Kg  laminated paper bags. Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistic results obtained in standard conditions)

Appearance White powder
Adjustment time Approx. 30 minutes (depending on weather conditions)
Paste shelf life Approx. 2 hours. (depending on weather conditions)
Initial adhesion > 1 N/mm2
Adherence after water immersion > 1 N/mm2
Adherence after heat ageing > 1 N/mm2
Adherence after freeze/thaw cycles > 1 N/mm2
Classified according to UNE EN 12004:2008  C2 TE 
Performance  4Kg/m2

 

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solution carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the
tests obtained under different conditions, all in accordance with the relevant regulation.