Pumaflex^® Fibrado

Technical Caracteristics

Waterproofing coating made up of an aqueous dispersion of acrylic copolymers, loads with high mechanical strength, additives and special pigments.

Advantages and Uses

• Waterproof.
• Good resistance to traction and high elasticity.
• Good homogenization of the product and easy application.
• Outstanding resistance to abrasion.
• Good filling of cracks and resistant to microcracking.
• Easy application and low tack.
• Contains cut fiber.

Suitable Substrates

NEW SUBSTRATES

• Concrete, cement, render, brick, stone, fiber cement, etc…. must be set, dry, firm and free of dirt and grease.
• Treat efflorescence or saltpeter with diluted acid solution, rinse and allow to dry.
• The surfaces should be free of moss and microorganisms, dry or slightly damp.
• If there are cracks, holes or chips, repair before applying the product.
• Apply the paint according to the instructions for use.

OLD SUBSTRATES

• Concrete, cement, render, brick, stone, fiber cement, etc…. must be set, dry, firm and free of dirt and grease.
• Treat efflorescence or saltpeter with diluted acid solution, rinse and allow to dry.
• Remove mold contamination with bleach or other suitable decontaminant, and also remove any loose paint or other building materials.
• On surfaces in poor condition, with lack of cohesion or damp problems, apply a water-repellent sealant beforehand.
• If there are cracks, holes or chips, repair before applying the product.
• Old paint should be brushed to remove loose particles, cleaned and degreased. 
• Apply the paint according to the instructions for use.

Application Procedure

• Stir until evenly mixed.
• Dilute the first coat by 5% with water.
• Apply the second and subsequent coats undiluted, crosswise to the application of the previous coat.
• For optimum performance and durability of the waterproofing, at least 1.5 l should be used per m² of surface. 

Recommendations

• If there are fillers or asphalts in the expansion joints it is recommended to “bridge them” appropriately with polyester elastic reinforcement.
• Where necessary, correct slopes to prevent water from pooling. 
• At the joints with vertical surfaces it will be necessary to reinforce with fiberglass or other suitable material applying Pumaflex anti-leak up to a height of 15 cm.
• Do not apply at temperatures below 5⁰C.
• Do not apply with relative humidity above 85% or on wet substrates.
• Do not apply under any circumstances if rain is forecast.
• Store in a cool, dry place.

Packaging and Storage

Containers of 4 and 15 L
Shelf life: 24 months in its sealed original packaging, in a cool, dry place protected from weather conditions and direct sunlight, avoiding exposure to temperatures lower than 5ºC or higher than 35ºC.

Technical data

(Statistical data obtained under standard conditions)

Legal Disclaimer

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.