Traditerm® Perfil cierre lateral
Protection and closing profile in External thermal insulation Traditerm Systems (SATE/ETICS). The TRADITERM® PERFIL CIERRE LATERAL protects and reinforces the side finishes of the Systems.TRADITERM® (thermal insulation), does not rust and is easy to install on site. It has a range of thicknesses to be chosen according to the thickness of the insulating panel used.
Additional information
Technical Caracteristics
aluminium profile.
Advantages and Uses
- Easy to apply.
- Protects and reinforces the sides of Tratiderm Systems (SATE/ETIC).
- It does not get rusted.
- Range of thickness to choose from according to the insulation panel used.
Application Procedure
Once TRADITERM® Perfil de Arranque has been paced, screw TRADITERM® Perfil Cierre to the substrate.
Lateral in any TRADITERM System (SATE/ETICS )side you may need to protect with this profile.
The screws used in order to fix the sides of the profiles should be place with a minimum separation of 30 cm between them.
The first screw should be placed with a distance below 5 cm from the profile's border.
Recommendations
- For a greater attachment place a screw every 30 cm.
- There should always be a fixation, with a distance inferior to 5 cm from the TRADITERM® Perfil Cierre Lateral border.
- Choose the correct closing profile according to the thickness of the insulating panel.
- The encounter between the substrate and TRADITERM® Perfil Cierre Lateral should be sealed using PUMALASTIC MS.
Packaging and Storage
10 units box->25 lineal meters.
The profiles should be stocked up in horizontal position.
Technical data
| Composition | (0,6±0,04 mm) |
| For Insulating panel thickness | 40, 50, 60, 70, 80, 90, 100, 120 mm |
| Profile length | 2,5 ±0,01 m |
Legal Disclaimer
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
Notas
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.