Implarest® PU
Implarest PU is a two-component semi-elastic cladding of polyurethane free from solvents. It prepares the surface for the application of water repellent claddings of great thickness and great resistance to abrasion.
Additional information
Features and applications
- It can be used as primer for the elastic cladding Morcemdry PU for water tightness treatments over concrete or mortar substrates, such as dams, canals, tanks or decanters.
- Safe drinking water deposits.
- Great adherence to the substrate.
- Negative pressures resistance.
- Impermeability.
- Abrasion resistance.
Substrates
Surfaces to be treated should be clean, without grease and dust in order to obtain an adequate adhesion. It is advisable to apply a pressure drip of sand or water (200 atm), which can also be sometimes replace by a mechanic or manual brushing / milling, etc.
Instructions for use
- Stir each component before mixing them to remove grounds.
- Mix completely component B with component A. This will ensure that the volume proportion between component A and component B is correct.
- Stir with an electric mixer at low speed (less than 600 rpm) for 4 to 5 minutes, until getting a homogeneous product.
- The product is generally applied by brush or roller and if used as a primer can be diluted between 5-10% with xylene (depending on the porosity of the support). It can also be projected and for this it is necessary to dilute it between 10-15% with xylene (consult with the technical department).
Cautions and recommendations
- Every mixing and application equipment should be cleaned with solvents.
- Tools should be cleaned while the product is still fresh before it polymerizes.
- Please consult our Technical Department for any other application method which has not been specified in this data sheet.
- For any information regarding the safety in handling, transportation, storing and use of the product please consult the tag and the updated version of the Safety Data Sheet of the product.
Packaging
10 kilos kits.
Implarest PU should be stored in it original packaging and in a dry place. Keep it between 5ºC and 30ºC. Once it has been open it should be used as soon as possible, as it considerably reduces its shelf life.
Shelf life: 1 year.
Technical data
| Properties | Value |
| Colour | Red/ Grey/ Ral color under request |
| Mixture relation (A+B) | 85/15 |
| Specific weight | 1.7 g/cm3 |
| Solids content | >99 % |
| Post – life 20ºC | 4 hours |
| Dry touch | 4-6 hours |
| Breathable | 24 hours |
| Time between layers | Previous layer must be dry- 72 hours maximum. |
| Advised average yield | 500 g/m2 |
| Advised average thickness | 250 – 300 micras |
| Put into service after | 3 days |
| Traction resistance | 26 Mpa |
| Concrete adherence | 2,5 N/mm2 (own cohesion) |
| Abrasion Taber (Load 500 gr) | <0,79 mg/cycle |
| Water absorption (% in weight after 6 days) | <3 |
| Negative presure resistance 2kg/cm2 | Satisfactory after 72 hours |
| Elongation of the tear | 2 % |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.