Paviland® Resina Alifática
Aliphatic polyurethane resin-based binder for creating and installing decorative natural stone and mineral chippings.
Additional information
Features and applications
- Continuous surfaces and coverings applied in-situ.
- Special applications for gravel aggregate and shredded rubber chippings, with a high resistance to yellowing, suitable for light and strong colours.
Instructions for use
- Before applying the binder, both the substrate or mould, as well as the aggregate or rubber to bind must be completely dry and free from any particles of dust, grease or other contaminating agents.
- The reaction of ALIPHATIC RESIN commences with atmospheric humidity or water vapour. The higher the temperature and % of environmental humidity, the faster the reaction time.
For applying in-situ:
- Pour the ALIPHATIC RESIN over the aggregate or rubber (see table of recommended doses) contained in the recipient used for mixing, homogenised with a low-speed mixer, or else by mixing manually for 2 -3 minutes until the correct consistency has been obtained.
- In order to avoid undesired effects, avoid direct contact with water (rain, intense spraying) during the first 24 hours of curing as this can interfere with the reaction of the product.
For any sprayed applications please consult our technical department.
Cautions and recommendations
- Apply at least 3.5 to 6% of ALIPHATIC RESIN over the mineral/stone chippings. The dosage will vary according to particle size and desired compaction.
- For surfaces subjected to heavy foot traffic or strong loads, please consult our technical department.
- Work tools should be cleaned with a solvent immediately after use.
Packaging
In opaque plastic container with net weight of 5 kg.
Store in the original unsealed packaging in temperatures from 15 - 25ºC in a dry, well-ventilated place. The product has a useful life of 6 months.
Dosage table
The dosage must be previously checked as the porosity or type of aggregate or mineral could require varying percentages. The following table shows the approximate % for creating decorative surfaces (for guidance purposes only).
| DOSAGE | TYPES |
| 3.5 - 4% | For non-porous stones of a diameter of 50 mm or above |
| 4 - 4.5% | For non-porous stones of a diameter between 5 and 50 mm |
| > 4.5% | For non-porous stones of a diameter less than 5 mm |
| 15% | For rubber floors made in situ (finishing layer) |
Technical data
| Appearance: | Translucent |
| Density at 25ºC: | 1.021 ± 0.020 g/cm3 |
| Viscosity at 25ºC: | 800 ± 200 cps |
| Contents in solid particles: | 100% |
| Flash point: | > 200ºC |
| % NCO: | 20.56 ± 0.20 % |
FINISHED PRODUCT CHARACTERISTICS
| TEST | STANDARD | RESULT |
| Stretch to break point (%) | UNE 53510 | - |
| Tensile strength (MPa) | UNE 53510 | - |
| Tear strength (N/mm) | UNE 53510 | - |
| Hardness (Shore A %) | UNE 53130 | - |
| Density (g/cm3) | UNE 53526 | - |
| Abrasion (mm3) | UNE 53527 | - |
| Dry to touch | 12 hours |
| Time between coats | 24 hours |
| Start up time 23ºC | 48 hours |
| Fully set at 23 ºC | 96 hours |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.