Paviland® Sport EPW Top
Two-part, epoxy resin-based primer in aqueous solution with mineral fillers, for the preparation of concrete bases before application of acrylic and epoxy-acrylic sports floors systems; for outdoor use.
Additional information
Composition
Acrylic-epoxy resins in aqueous medium with mineral fillers.
Features and applications
- Wide range of colours.
- Easy application.
- Water-based product.
- Indoor and outdoor use.
- Continuous-use sports surfaces.
- High-durability bicycle lanes.
- Indoor garages and outdoor parking areas for low-volume traffic.
- Finishing coat for PAVILAND SPORT AC Systems.
- Resistant to oil spills.
Substrates
- All base materials must be durable, stable, sound and clean, in addition to being free of dust, form release agents (e.g. paint stripper), organic products, etc.
- Sealant for concrete bases: prior application of PAVILAND SPORT EPW PRIMER is required (consult the corresponding technical specifications for correct assessment of the concrete).
- Finishing for High-Performance Sports Systems on concrete bases: prior application of PAVILAND SPORT EPW PRIMER is required (consult the corresponding technical specifications for correct assessment of the concrete) as well as the intermediate layer of PAVILAND SPORT EPW FINISH, which must be dry.
- Finishing for High Performance Sports Systems on asphalt bases: prior application of PAVILAND SPORT AC BASE is required (consult the corresponding technical specifications for correct assessment of the asphalt base) as well as the intermediate layer of PAVILAND SPORT EPW FINISH, which must be dry.
Instructions for use
- Mix the separate A and B components.
- Add all of component B to component A and mix with an appropriate mixer at low speed until a uniform consistency has been obtained.
- Apply the product with an airless sprayer or brush.
- The second coat can be applied after approximately 2 hours, provided that the first coat is completely dry.
Cautions and recommendations
- Do not apply in temperatures below 10°C or above 30°C.
- Do not apply when there is a risk of frost, rain, strong winds or direct sunlight.
- Wear protective gloves and goggles during application. In the event of direct contact with the eyes, wash with plenty of soap and water, and seek the advice of your doctor.
- In the event of contact with the skin, wash with water before the product dries.
- Keep out of the reach of children.
- Remember to clean all equipment and tools with water immediately after use. Once the product has hardened, it will only be possible to clean such equipment and tools mechanically.
- Do not eat or smoke during handling.
- All empty containers must be discarded in accordance with current legislation.
Packaging
Containers of 20 (18.5 + 1.5) kg.
The product can be stored for up to one year in its original sealed containers, in a dry and well-ventilated area, at temperatures between 10°C and 30°C, and out of direct sunlight and protected from the elements.
Colour range
Yellow ochre, blue, white, grey, red and green.
Technical data
(Statistical results obtained under standard conditions).
| Appearance | A: white paste – B: coloured paste |
| Approximate density of the mixture | 1.2 kg/dm3 |
| Weight ratio of the mixture (A: B) | 86 : 14 |
| Active lifetime of the mixture (*) | 30 min |
| Wait time before application of the second coat (*) | 2 hours |
| Resistance to abrasion – 8-day Taber test (CS10/1000 g/1000 cycles) | 27 mg |
| Slip resistance according to the Technical Building Code (CTE) | > 45 (class 3) (**) |
| Approximate yield | 0.2 kg/m2/layer |
(*): These times refer to a temperature of 23°C, and 55% relative humidity. Times are shorter at higher temperatures, and longer at lower temperatures.
(**): Slip resistance of the High-Performance Sports System
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.