Puma CE
Tile adhesive for indoor floor tiling and cladding jobs suitable for bonding ceramic tiles with a medium-high absorption rate.
Additional information
Composition
Product based on high resistance cement, selected aggregates and additives.
Features and applications
- To be applied indoors.
- Suitable for ceramic tiles with a medium-high absorption rate.
- No need to wet tiles or substrates thanks to its high water-retaining capacity.
- Non slip. Excellent initial adherence.
- Long open time. Allows rectification.
Substrates
- Conventional cement-based substrates.
- Substrates must be resistant, stable, sound and clean, free of dust, demolding agents, organic products, etc.
- All substrates must have the appropriate flatness. Otherwise, smooth down up to 5 mm with the same product 48 hours prior to bonding.
- In case of greater thickness should be used:
- On floors: Depending on the particular need use 10R NIVELAND 10 R or PAVILAND RECRECIDO AUTONIVELANTE.
- On walls: mortars with adequate tensile strength with drying shrinkage already completed.
- In case of hot or windy weather conditions or when applying over absorbent substrates, it is advisable to wet the substrate and wait till the thin layer of water disappears. Do not apply on clay or on paint
Instructions for use
- Add water and mix by hand or mechanically until it takes on an even and workable consistency.
- Let the mixture stand for 5 minutes and remix.
- Spread the mixed product on the substrate with a trowel to a maximum surface area of 2m2.
- Spread with a notched trowel to adjust thickness (see chart).
- Lay the tiles, press and make small rotation movements to ensure that the glue gets in total contact with both surfaces.
- Observe construction joints (expansion, contraction, fraction, perimeter corner joints) and the joints between the cement slabs (minimum 2mm).
- Joints should be grouted 24 hours after if on vertical surfaces, and 48 hours after if on floorings. Use the appropriate mortar from the MORCEMCOLOR range depending on the type of joint.
NOTE: For better results lay tiles as soon as possible after spreading.
Notched-trowel panel
| Maximum weight on vertical surfaces: 20 kg/m2 | ||
| TILE FORMAT | NOTCHED TROWEL | BONDING |
| < 100 cm2 | U4 (4 x 4 x 4) | Simple |
| ≤ 450 cm2 | U6 (6 x 6 x 6) | Simple |
| ≤ 900 cm2 | U6 (6 x 6 x 6) / U9 (9 x 9 x 9) ó n10 | Double-Simple |
| > 900 cm2 | U9 (9 x 9 x 9) ó n10 | Double |
Cautions and recommendations
- Do not apply below 5ºC nor above 30ºC.
- Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
- Do not apply in areas where water may accumulate.
- Under extreme weather conditions (gusty winds or high temperatures) drying may occur faster.
- On floor areas larger than 30 m2, leave partition joints to be filled with a flexible material among PUMALASTIC range.
- In case of Indoor floor tiled areas larger it is recommended to leave a free perimeter joint between the tiles and the wall or pillar of about 5 mm hidden by the plinth. These joints must be filled with a deformable grout among PUMALASTIC range.
- For gypsum based substrates, use PEGOLAND ESPECIAL YESO o PEGOLAND PORCELÁNICO YESO, or PEGOLAND PROFESIONAL line, voiding slaked or poor plaster.
- In case of tiles reinforced with fiberglass mesh on their back, ask the technical department.
- Do not use the technique known as by globs.
- Working and setting times of the adhesive depend on the temperature, air streams, and the absorption of tiles and substrates.
Packaging
25 kg plastic-lined paper bags
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.
Technical data
| (Statistical data obtained under standard conditions) | |
| Aspect | WHITE or GREY powder |
| Adjustment time | Approx. 20 min. (depending on weather conditions) |
| Paste shelf life | Approx. 2 hours (depending on weather conditions) |
| Initial tensile adhesion strenght | ≥ 0,5 N/mm2 |
| Tensile adhesion strenght after water inmersion | ≥ 0,5 N/mm2 |
| Tensile adhesion strenght after heat ageing | PND |
| Tensile adhesion strenght after freeze-thaw cycles | PND |
| Approximate yield | Simple gluing: 4 Kg/m2 |
| Double gluing: 6 Kg/m2 | |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.