Pumacril Decoración Satinada

Satin plastic paint intended for the protection and decoration of walls made with all kinds of mineral materials (concrete, cement, plaster, etc.) both indoors and outdoors.


Download technical data sheet


Additional information

Composition

Coating formulated from aqueous dispersal of vinyl resin, pigments and special additives.

Features and applications

  • Excellent cleaning features and resistance to wet rubbing.
  • Great whiteness and opacity.
  • Weatherproof and UV resistant film.
  • Magnificent adherence on exterior and interior vertical walls of plaster concrete and cement-based construction materials.
  • Excellent shine retention.

Substrates

NEW SURFACES

  • Remove dust, greases or any other possible contaminants.
  • Apply a first coat of FIJAMOR diluted in 2 or 3 parts of water, to make uniform the absorption of the substrate.
  • Apply the paint according to the given instructions.

OLD SURFACES

  • Remove mould contamination as well as loose parts of paint or other construction materials.
  • Level any possible irregularities with a suitable plaster. Let it dry and sand the area.
  • Apply a first coat of FIJAMOR diluted in 2 or 3 parts of water, to set and make uniform the absorption of the substrate.
  • Apply the paint according to the given instructions.

Instructions for use

NEW SURFACES

  • Remove dust, greases or any other possible contaminants.
  • Apply a first coat of FIJAMOR diluted in 2 or 3 parts of water, to make uniform the absorption of the substrate.
  • Apply the paint according to the given instructions.

OLD SURFACES

  • Remove mould contamination as well as loose parts of paint or other construction materials.
  • Level any possible irregularities with a suitable plaster. Let it dry and sand the area.
  • Apply a first coat of FIJAMOR diluted in 2 or 3 parts of water, to set and make uniform the absorption of the substrate.
  • Apply the paint according to the given instructions.

Cautions and recommendations

  • Do not apply under 5ºC temperatures.
  • Do not apply Do not apply with relative humidity higher than 85% or on wet substrates.
  • Storage: In its well-closed original container, in cool, dry places in a sheltered place not exposed to direct sunlight, and avoiding exposure to temperatures below 5ºC or above 35ºC.

Packaging

4 and 15 L containers
 

Technical data

ASPECT OF THE DRIED FILM VALUE ACCORDING TO SPECIFICATIONS
Colour White
Finish semi- matt UNE-EN 1062-1
85º shine 42,4 UNE-EN ISO 2813
CHROMATIC CORDINATE  L* 95,7 UNE 48073
CHROMATIC CORDINATE C* 1,12 UNE 48073
CHROMATIC CORDINATE h* 99,6 UNE 48073 
BERGER WHITENESS 85-88 UNE 48073
OPACITY <95% UNE-EN 13300

 

PHYSICAL PROPERTIES VALUE ACCORDING TO SPECIFICATIONS
Density 1,28 Kg/l UNE-EN ISO 2811-1
pH 7,5 INTERNAL
Viscosidad 80 dPas (50 rpm; Husillo R6) UNE-EN ISO 2555
Finura dispersión 20 UNE-EN ISO 1524

 

REGARDING ITS FORMULATION VALUE ACACCORDING TO SPECIFICATIONS
Non-volatile matter content 50% UNE-EN ISO 3251
Maximum VOC content allowwed 30 g/L 2004/42/II A Classification
MAximum VOC content of the product 30 g/L 2004/42/II A Classification

 

APLICATION PROPERTIES VALUE ACCORDING TO SPECIFICATIONS
Theoritical performance 9-11 m2/L UNE 48282
Dry touch time 1 Hour UNE 48301
Total dry time 2 Hours UNE 48301
Thinner Water -
First hand solution 10 -15% -
Second hand and subsequent dilutions 5 -10% -
Repaint interval 3-4 Hours -

 

 

OTHERS SPECIFIC PROPERTIES VALUE ACCORDING TO SPECIFICATIONS
Web rub resistance Class 1 UNE-EN ISO 11998

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.