Pumaplast®
Powder filler for plastering, to smooth out, fill in cracks, scrapes, holes, etc., ideal for plastering plasticized Gotele surfaces.
Additional information
Technical Caracteristics
Product based on inorganic mineral fillers, plaster, and additives.
Advantages and Uses
- For general interior use on substrates such as plaster, gypsum, drywalls, mortars, concrete, old paints, etc.
- Smoothing and levelling of plastic-coated textured surfaces.
- Filling small defects, holes, scratches, cracks, fissures, etc.
- Fine, hard finish with high whiteness, suitable for all types of plastic paints, wallpaper, etc. Q4
- Easy preparation and application using a trowel or spatula.
- Easy sanding and minimal shrinkage.
- Reduces substrate absorption, increasing paint coverage.
- Good adhesion
- Allows fresh-on-fresh application.
- Can be applied manually or by spraying.
Suitable Substrates
- Substrates must be free of dust, grease, wax, etc.
- Any poorly adhered paint must be removed.
- Highly absorbent substrates should be pre-treated with a primer or sealer.
- Do not apply on frozen, extremely hot, wet substrates, or those with high moisture content.
Application Procedure
- Mix 1 kg of product with 0.5 L of water, adding lesser amounts of water until the optimal working consistency is achieved, resulting in a homogeneous and consistent paste.
- Mix manually or with a mixer not exceeding 500 rpm.
- It is recommended to apply with a smooth trowel or stainless-steel spatula.
- Clean tools with abundant water after use.
Recommendations
- Do not apply under 5ºC nor above 35ºC.
- Do not apply on surfaces with moisten above 85%.
- Do not apply if there is a risk of frost.
Packaging and Storage
5 and 15 kg laminated paper sacks.
Store up to 12 months in its original closed container, away from extreme weather conditions and humidity.
Technical data
(Statistical data obtained under standard conditions)
| Aspect | WHITE powder |
| Solvent | Water |
| Apparent density of powder | Aprox. 0,700 g/cm³ |
| Apparent density of paste | Aprox. 1,400 g/cm³ |
| Grains seize distribution | < 200 µm |
| pH | 7 ± 0.5 |
| Adhesion on gypsum and plaster | > 0.1 N/mm² |
| Maximum thickness per layer | 5 mm. |
| Mix shelf life | > 6 hours at 20ºC |
| Approximate Yield | Aprox. 1.5 m²/Kg per mm of thickness |
| Dry | 3-4 hours per mm applied (variants depending on environmental conditions and supports) |
| Sanding/painting | After it is dry |
Legal Disclaimer
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.