Traditerm® NC

Hydraulic mortar used as an adhesive for expanded polystyrene insulation plates  (TRADITERM Panel EPS), in graphite expanded polystyrene (TRADITERM Panel EPS-G), in mineral wool (TRADITERM Panel MW) and natural cork (TRADITERM Panel Cork), in the exterior thermal  insulation system TRADITERM (SATE/ETICS). This mortar is ideal for exterior thermal insulation system, it has great adhesion, easy to apply and does not spread the flame. It is also water vapour permeable.
 

998-1 - GP W0 GBC ECO

Download technical data sheet


Additional information

Composition

Made from hydraulic conglomerates, selected aggregates and additives.

Features and applications

  • Especially made for non conventional  substrates cladding.
  • Manual application
  • Excellent adherence.
     

Substrates

  • Mortar renderings or other substrates of a similar mineral nature with a certain degree of porosity.
  • OBS  wood plates
  • Ceramic tiles or very well adhered to tiles.
  • Paint in good state 
  • Waterproof bricks.
  • Substrates must be resistant, stable, healthy and clean, free of dust, remains of release agents and organic products.
  • Take into account  the resistance compatibility of the substrate with  the mortar used.
  • In case of hot, wind or very absorbent substrates, wet the substrate and wait until the complete film of water disappears.
  • Do not apply on top of plaster.
     

Instructions for use

  • Mix the product with water until getting a homogeneous paste: 20% approximately.
  • Fix the insulating plates to the substrate, using TRADITERM NC mortar.

DENTED TROWEL METHOD

  • Spread and comb the TRADITERM adhesive on the insulating panel, using the notched trowel. This way a homogeneous distribution of the adhesive is obtained over the plaque.
  • Remove the TRADITERM bit close to the plaque (2cm approximately).
  • This is done when the flatness of the substrate is <5 mm using a 2 m ruler to measure it.

Cautions and recommendations

  • Substrates (bricks, plasters and concrete) must be clean (free of dust, traces of paint in bad condition, greases, release agents, etc.)
  • The person in charge must make sure that, in the event of applying the product on top of any other paint, this pain is in good state.
  • Substrates with greater than 1 cm, incline, should be previously regularized.
  • Insulating panels should never cover the building's expansion joints. As a solution, please use the expansion profile.
  • Protect the upper part of the façade to avoid possible water filtration.
  • The adhesive does not exempt the placement of anchor plugs.
  • Do not apply the product under extreme weather conditions.
  • Do not apply it under the rick of freeze, rains, heavy winds or direct sun light.
  • Do not apply in areas where there might be stagnant water. 
  • Under extreme weather conditions (heavy wind or high temperatures) the drying process may be faster than usual.

Packaging

5 kg laminated paper sacks.
1 year storage in its original packaging, away from extreme weather conditions and humidity.
 

Technical data

(Statistic results obtained in standard conditions)

Aspect White powder
Permeability to water vapour < 20
Adhesion SUBSTRATE N/mm2
Concrete > 1
Tile (glazed face) > 1
EPS > 0,2 break EPS
OSB > 0.2 break OSB
Paint (in good state) > 1
Tile > 1
Waterproof brick > 1
Classification according to UNE-EN 998 1 GP W0
Approximate yeld 4-5 kg/m2

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.