Morcem^® Cal Acabado Extrafino CR W0

Technical Characteristics

Product based on NHL 3,5 natural hydraulic lime, CL90 air lime, pozzolan, mineral fillers and other additives. Contains no cement.

Advantages and Uses

• Internal and external render. 
• Suitable for refurbishment due to its high compatibility with traditional systems.
• For indoor and outdoor application in new-build construction where improved living conditions are required compared with cement-based mortars.
• Highly permeable to water vapour, allowing the substrate to breathe.
• High adhesion to the substrate and excellent plasticity.
• Smooth and burnished finish.
• Manual application.
• Fine decorative finish for lime mortars.
• Mortar with a low environmental footprint, manufactured with mineral-origin raw materials. It has an Environmental Product Declaration (EPD).
   

Suitable Substrates

• On substrates previously treated with MORCEM® CAL ACABADO.
• Thoroughly dampen the substrate and wait until the surface water film has disappeared before application.
• Do not apply over gypsum or paint.
   

Application Procedure

MANUAL APPLICATION

• Add water (6,0-6,3 l per 15 kg bag) and mechanically mix until a homogeneous and workable consistency is obtained.
• Mix, adjusting the water to the recommended amount and avoiding excess, allowing the desired consistency to develop through prolonged mixing. 
• Prepare the substrate by dampening it beforehand and wait until the surface water film has disappeared.
• Spread the mixed product over the substrate with a trowel, pressing firmly onto the substrate to ensure adhesion and prevent air entrapment.
• Apply to a thickness not exceeding 2 mm.
• At least 24 hours before application, thoroughly dampen the substrates. Cure the applied material for 24 hours after application. Wait 24-48 hours per cm. of base render thickness before applying Morcem® Cal Acabado Extrafino.
   

Recommendations

• Do not apply below 5ºC or above 30ºC.
• Do not apply where there is a risk of frost, rain, strong winds or direct sunlight.
• In extreme weather conditions (strong winds or high temperatures), gently spray the product with water on the day after application.
• Do not apply directly onto the wall substrate (brick, concrete block, etc.)
• Do not add water to mortar that has already been mixed once it begins to harden.
   

Packaging and Storage

15 Kg plastic-lined paper bags.
Store for up to 1 year in the original sealed packaging, protected from weather and moisture.
 

Technical data

Appearance	Off-white powder
Mixing water	41±1
Mixed product density	1,65 ± 0,2 g/cm3
Water vapour diffusion coefficient	µ ≤7
Classification according to UNE EN 998-1	CR CSI W0
Approximate coverage	1,0 kg/m2 per mm thickness
Standard/regulation, version applied and result assessment:
French Regulation of March and May 2011 (DEVL 1101903D and DEVL 1104875A), amended in February 2012 (DEVL1133129A)
French CMR compounds. Regulation of April and May 2009 (DEVP 0908633A and DEVP0910046A)	Pass
Italian CM Edilizia DM 23 June 2022, decree of 6 August 2022	Pass
ABG/AgBB Committee for Health-related Evaluation of Building Products (September 2024)	Pass
Belgian Regulation. Royal Decree of May 2014 (C-2014/24239)	Pass
EMICODE (February 2025)	EC 1 PLUS
Indoor Air Comfort. Indoor Air Comfort 9.0 June 2023	Pass
Indoor Air Comfort GOLD. Indoor Air Comfort GOLD 9.0 June 2023	Pass
Blue Angel (DE-UZ 198): DE-UZ 198 for "Low-emission interior renders", January 2019	Pass
BREEAM International. BREEAM International New Construction v6.0 (2021)	Exemplary level
BREEAM NOR. BREEAM-NOR v6.1.1 New Construction (2024)	Exemplary level
EU Taxonomy. EU Regulation 2020/852 of the European Parliament and of the Council	Pass

CE Mark

GRUPO PUMA ESPAÑA, S.L Avda. AGRUPACIÓN CÓRDOBA, Núm.17 14014 CÓRDOBA 26
MORCEMCAL ACABADO EXTRAFINO Nº: 860040 EN 998-1 Natural hydraulic lime-based smoothing mortar for rendering and decoration, CR W0, for application over Morcemcal Acabado indoors and outdoors at an average thickness of 2 mm.
Reaction to fire	Class A1
Water absorption	W0
Water vapour diffusion coefficient	µ≤7
Adhesion	≥ 0,1 N/mm2 Failure mode B
Thermal conductivity: (λ10, dry)	0,3 W/mK (tabulated value)
Durability	Assessment based on provisions valid at the intended place of use of the mortar
Dangerous substances	See Safety Data Sheet

Environmental Product Declaration (EPD)

Mortar manufactured using aggregates sourced close to the production centres, reducing greenhouse gas emissions associated with their transport, and manufactured at production centres with Environmental Management Systems certified in accordance with ISO 14001, demonstrating a firm commitment to sustainability and environmental protection.

Mortar with a Type III ecolabel (the most demanding category), with an Environmental Product Declaration externally verified by AENOR.
 

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.