Morcem^® Texture OC CSIII W2

Technical Caracteristics

Product based on high resistance cement, selected aggregates, special additives, pigments and synthetic resins.

Advantages and Uses

• To be applied directly on the brickwork. No need for a previous plastering.
• To be applied indoors and outdoors.
• Waterproof cladding.
• Permeable to water vapour, allowing the substrate to breathe.
• No cracking.
• Wearing resistant. Fading resistant.
• Wide range of decorative finishes by application of molds or rollers.

Suitable Substrates

• Conventional cement and brickwork based substrates.
• Substrates must be resistant, stable, sound and clean, free of dust, demolding agents, organic products, etc.
• In case of hot or windy weather conditions or when applying over absorbent substrates, it is advisable to wet the substrate and wait until the thin layer of water disappears.
• In particular points (union between different materials, top slabs, pillars, roller blind boxes, angles in the door and window frames, etc.), prepare the mortar with glass fiber mesh to avoid fissures.
• With low-porosity substrates, apply a priming coat (IMPLAFIX) or improve roughness by mechanical means.
• Do not apply on clay or on paint.

Application Procedure

The stamped one coat mortar requires to follow a series of steps during application which are not very different from conventional rendering jobs.

The steps to be taken are as follows:

• Reinforce the substrate with a mesh on stressed areas and prepare partition joins as in a conventional one-coat system.
• Mix preferably by mechanic means until a homogenous paste is obtained.
• Spread a layer of 10mm max on the substrate. Thicker coatings can be achieved depending on desired finish texture.
• Wait for 15-20 minutes (depending on weather conditions this may vary) before texturing MORCEM TEXTURE. When the product does not adhere to the naked fingertip it is a good indication that the product is ready to be textured.
• Spray a small quantity of demolding liquid DESMOLDEANTE MORCEM TEXTURE on the render and on the mold/roller. To ensure the substance does not stick, apply again  the separating demolding agent to the roller approximately every ²m.
• Run the roller on the render to create a pattern. Adequate pressure must be exerted. Hard enough so the stamping is clear but soft enough not to produce pressure waves on the render. Small stamping defects should be fixed immediately during the stamping process. Either when applying the substance, or when applying it to the roller, if the edges are stained with paste as in continuous grooves, this effect is not necessarily aesthetically pleasing and should be corrected at the time.
• Option: 24 hours after application MORCEM TEXTURE can been pigmented by moistening the texture and spreading a dilution of one or many pigments on the stamped render.
• Option: To increase the resistance of the finish, spray RESINA MORCEM TEXTURE on the exiting MORCEM TEXTURE, otherwise use a roller with the lowest yield possible (white foam roller or varnish roller). Apply an even coating so avoiding the generation of straight lines of excess product which may yield a poor finish.

Recommendations

• Do not apply below 5ºC nor above 30ºC.
• Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
• It is not advisable to apply on horizontal or sloped surfaces.
• Take care not to contaminate/stain other surrounding elements when spraying RESINA MORCEM TEXTURE

Packaging and Storage

25 kg plastic-lined paper bags.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.