Paviland® Primer Ceramic
Adherence promoter, specially developed for the placement of cementitious floorings on non-porous and/or
vitreous surfaces such as ceramics, stoneware, marble, stone, very low porosity concrete, polished cement,
etc.
Additional information
Advantages and Uses
- Suitable on sub floor heating systems
- Good wetting properties
- Good adhesion to non porous materials
- Binding primer for installations
- Binding primer for levelling compounds
- Easy to apply
- Can be diluted with water
Suitable Substrates
- Mastic asphalt screed.
- Calcium sulphate (flow) floors (no moisture barrier).
- Wooden planks, wood fibre boards.
- Chipboards V100 (E1), OSB boards.
- Stone, ceramic, terrazzo, tiles.
- Unlaminated gypsum fibre boards.
- Cement floors.
- Cement floors with residual moisture.
Application Procedure
- Paviland Primer Ceramic is a ready-to-use primer for non-absorbent or dense surfaces such as stone, ceramic, terrazzo, and tiles.
- Before use, the container should be shaken well to disperse any settled material.
- The primer must not be diluted.
- Apply a thin, even coat using a medium-pile roller. Avoid over-application and ensure no puddles form.
- Allow the Paviland Primer Ceramic to dry for approximately 2–3 hours, depending on site conditions such as substrate type, ventilation, humidity, and temperature. Once dry, the surface will show a hard, translucent red film with fine quartz aggregate.
- Self-levelling compounds should be applied within 24 hours of primer application. If the primed surface is exposed for more than 48 hours or becomes dusty, a fresh coat of Paviland Primer Ceramic must be applied before proceeding.
Recommendations
- The subfloor must be checked according to the standard DIN 18356, DIN 18365, DIN 18367 or corresponding national standards. The subfloor shall be resistant to pressure and tension, free of cracks, must have sufficient surface strength, be permanently dry, level, clean and free of anti- adherents, sinter layers etc.
- Calciumsulfate (flow) floors and magnesite floors must be permanently dry, cement floors with residual moisture may receive as damp proof membrane by applying the Paviland Primer Ceramic.
- The maximum admissible residual moisture for cement floors is 3 CM%.
- The substrate must be always dry or slightly moistened but never puddly.
- Do not apply the product under temperatures of 15ºC nor above 35ºC.
- Within 72 hours after application, levelling compounds can applied on primer.
Packaging and Storage
10 Kg jerry can
Store up to 1 year in its original closed container, away from extreme weather conditions and humidity.
Technical data
(Statistic results obtained under standard conditions)
| Colour | Red |
| Drying time on non absorben sub floors | 90 min |
| Drying time on calcium sulphate floors, gypsum fibre boards,sanded mastic asphalt screed | 12 hours |
| Coverage | 125 g/m2 |
Legal Disclaimer
The instructions for use are given according to our tests and knowledge and do not imply any commitment by PIDILITEPUMA MEA CHEMICALS LLC nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
PIDILITEPUMA MEA CHEMICALS LLC is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of PIDILITEPUMA MEA CHEMICALS LLC exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by PIDILITEPUMA MEA CHEMICALS LLC's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
PIDILITEPUMA MEA CHEMICALS LLC is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of PIDILITEPUMA MEA CHEMICALS LLC exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by PIDILITEPUMA MEA CHEMICALS LLC's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.