Paviland^® Solera Autonivelante

Technical Caracteristics

Product based on cement, selected aggregates and additives.

Advantages and Uses

• High levelling capacity 
• Interior floors: bonded up to 50 mm and screeds for thicknesses between 50 and 100 mm 
• Suitable for floors with under floor heating 
• Easy to apply thanks to its high fluidity and flatness.

Suitable Substrates

• Substrates must be resistant, stable, sound and clean, free of dust, demoulding agents, organic products, etc. 
• Before applying PAVILAND SOLERA SELF-LEVELLING compound, repair any cracks and/or fissures on the substrate with products from our Niveland, Paviland or Morcem Rest ranges, according to the nature of the substrate and repair to be made. 
• For bonded floors (thicknesses lower than 50 mm) to concrete resistant substrates, first apply PAVILAND PRIMER R. For other substrates such as marble, ceramic etc, please consult our technical department. 
• Floating screeds for thicknesses between 50 and 100 mm over insulating substrates, plastic membranes or vapour barriers. For other types of substrates please consult our technical department

Application Procedure

• Define and mark the maximum dimension of the floor.
• Mix the product with water (4.1-4.6 L per 25 kg bag) mechanically, with a low speed mechanical mixer (approx. 500 rpm) until a uniform mixture without lumps has been obtained. The exact quantity of water is very important to avoid product separation, high shrinkage and lowering of strengths.
• Leave the mixture to rest for 2 minutes.
• For large surfaces it is recommendable to pump the mixture with double helicoidal pump at 20 to 40 litres/minute. This operation permits the maximisation of using times.
• Spread manually with a metal levelling trowel once the primer has hardened. Next, pass a nylon spiked roller.
• Respect structural joints and make perimetral  and partitioning joints.
• Paviland Solera Self-levelling compound must be protected by ceramic, wood, linoleum, etc.

Recommendations

• Do not apply under 5ºC nor above 30ºC.
• Do not apply when there is a risk of frost, strong wind or direct sun.
• Not recommended for exterior use.
• Do not apply on floor with humidity or with a risk of having it.
• Use gloves or protective goggles when applying product.
• Keep out of the reach of children. 
• Do not add sand, cement or any other product that modifies the original formula.
• Once the product has been mixed and the resting time has occurred, do not add additional water₂
• For floors larger than 20 m or longer than 10 lineal metre it is advisable to make partitioning joints, delimiting panels with 6 mm joints that can be sealed with PUMALASTIC MS or PU. 
• Movement joints on the original substrate must be respected and permiteral joints made.
• The surface coat must be protected from drying too quickly, especially in conditions with high temperatures and/or strong winds.
• Before laying the final flooring check the residual humidity of the floor and confirm it is adequate for the type of flooring to be installed.

Packaging and Storage

25 kg laminated paper bags. Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)

CE Mark

GRUPO PUMA SL Avda. AGRUPACIÓN CÓRDOBA, Núm. 17 14014 CÓRDOBA  15 Nº: 501863-01
EN 13813 PAVILAND SOLERA AUTONIVELANTE Self-leveling screed mortar of normal-setting cement, type CT C25 F5, for bonded interior screeds up to 50 mm and unbonded up to 100 mm.
Reaction to fire	Class A1
Emission of corrosive substances	CT
Compressive strength	C25
Bending strength	F5

Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.

Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.