Pegoland® Fix Plus D2

Ready to use adhesive made with resins, and specific additives and agents. Suitable for fixing any kind of ceramic cladding on vertical interior or exterior substrates. Highly flexible. Ideal for gluing exhibitions on wood and old tiles. This adhesive is perfect for use on deformable supports.

12004 - D2 Casita_MuroIntExt

Download technical data sheet


Additional information

Advantages and Uses

  • Ready to use. No addition of water is necessary.
  • Very flexible.
  • Recommended for deformable substrates.
  • Recommended to fix tiles on carton-gypsum boards.
  • Application of polystyrene boards on mortar.
  • Fixing by points of insulating panels.
  • Tiling on well preserved surfaces made of gypsum.
  • Tiling on well preserved painted surfaces.
  • Temporary fixing of tiles on wood.
  • Fixing tile over tile.

Suitable Substrates

  • Substrates must be clean and free of dust, oil, paint, loose particles, etc.
  • It is very important that the substrates are completely dry before the application.
  • The substrate must be completely hardened.
  • Substrates should be resistant , stable, healthy and clean

 

Application Procedure

  • Mix Pegoland Fix Plus to obtain a homogenous paste.
  • Spread in small areas using a max 4mm saw to level.
  • Place tiles on the fresh adhesive, pressing and with a slight sliding or twisting action to get a good contact of the whole surface of the tile.
  • Observe construction joints (expansion, contraction, fraction, perimeter corner joints) and the joints between the cement slabs (minimum of 2 mm inside and 5 mm outside).
  • Wait 24 hours before grouting. Use the appropriate mortar from the MORCEMCOLOR range depending on the type of joint.

Recommendations

  • Do not apply at temperatures below 5ºC nor above 35ºC.
  • Do not apply with a saw notched trowel larger than 4mm.
  • Do not apply in areas continuously exposed to humidity.
  • Do not apply over metals.
  • Do not apply under direct sunlight or on hot substrates.
  • Do not set non absorbant tiles on non absorbant substrates.
  • Maximum tile weight is 30Kg/m² and maximum size is 1600cm² (as in 40x40) when applying with Pegoland Fix Plus.
  • Format limit is 300cm2 if on exteriors.
  • Apply adhesive on the substrate and on the tile when tiles are equal or larger than 900cm².
  • In case of tiles reinforced with fiberglass mesh on their back, ask the technical department.
  • Do not use the technique known as by globs.
  • Working and setting times of the adhesive depend on the temperature, air streams, and the absorption of tiles and substrates.

Packaging and Storage

2,6 and 25Kg containers
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)
Aspect Tixotropic paste
Adjustment time > 40 min.
Initial shear adhesion ≥ 1,0 N/mm2
Shear adhesion after heat aging ≥ 1,0 N/mm2
Adherencia a cizalla a alta temperatura ≥ 1,0 N/mm2
Adherencia a cizalla después de inmersión en agua ≥ 0,5 N/mm2
UNE-EN 12004 Classification D2
Approximate yield 2 a 3 Kg/m2

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

 

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.