Resina Aglutinante Aromática
Polyurethane resin-based binder, for creating decorative surfaces with rubber and aggregate chippings.
Additional information
Advantages and Uses
- For binding rubber panels and flooring in children's play areas and continuous applications installed in-situ.
- For creating surface layers in clear colours it is advisable to use ALIPHATIC RESIN.
Application Procedure
- Before applying the binder, both the substrate or mould, as well as the aggregate or rubber to bind must be completely dry and free from any particles of dust, grease or other contaminating agents.
- The reaction of the AROMATIC RESIN commences with atmospheric humidity or water vapour. The higher the temperature and % of environmental humidity, the faster the reaction time.
FOR APPLYING IN-SITU:
- Pour the AROMATIC RESIN over the aggregate or rubber contained in the recipient used for mixing, homogenised with a low-speed mixer, or else by mixing manually for 2 -3 minutes until the correct consistency has been obtained.
- In order to avoid undesired effects, avoid direct contact with water (rain, intense spraying) during the first 24 hours of curing as this can interfere with the reaction of the product.
LARGE-SCALE APPLICATIONS:
- In order to guarantee top performance and quality for large-scale use, please consult our technical department on the correct temperatures, condition of moulds and type of demoulding agents to be used.
For any sprayed applications please consult our technical department.
Recommendations
- Apply at least 13% of AROMATIC RESIN to shredded rubber chippings for the base layer. The dosage will vary according to particle size and desired compaction.
- Apply at least 15% of AROMATIC RESIN to shredded rubber chippings for the surface layer. The dosage will vary according to particle size and desired compaction.
- For flooring with thicknesses lower than 22 mm it is essential to apply a primer. Please consult our technical department who will advise you on the best options, according to your requirements.
- For surfaces subjected to heavy foot traffic or strong loads, please consult our technical department on the type of application and maximum thickness per layer.
- Work tools should be cleaned with a solvent immediately after use.
Packaging and Storage
In opaque plastic container with net weight of 25 kg.
Store in the original unsealed packaging without between a temperature of 15 - 25ºC in a dry, well-ventilated place. The product has a useful life of 6 months.
Dosage table
The dosage must be previously checked as the porosity or type of aggregate or mineral could require varying percentages. The following table shows the approximate % for creating decorative surfaces (for guidance purposes only).
| DOSAGE | TYPES |
| 3.5 - 4% | For non-porous stones of a diameter of 50 mm or above |
| 4 - 4.5% | For non-porous stones of a diameter between 5 and 50 mm |
| > 4.5% | For non-porous stones of a diameter less than 5 mm |
| 13% | For rubber chips pavements applied in situ (base coat) |
| 15% | For rubber chips pavements applied in situ (finish coat) |
Technical data
| Appearance: | Translucent |
| Density at 25ºC: | 1.061 ± 0.020 g/cm3 |
| Viscosity at 25ºC: | 4400 ± 200 cps |
| Contents in solid particles: | 100% |
| Flash point: | > 200ºC |
| % NCO: | 9.65 ± 0.20 % |
FINISHED PRODUCT CHARACTERISTICS
| TEST | STANDARD | RESULT |
| Stretch to break point (%) | UNE 53510 | - |
| Tensile strength (MPa) | UNE 53510 | - |
| Tear strength (N/mm) | UNE 53510 | - |
| Hardness (Shore A %) | UNE 53130 | - |
| Density (g/cm3) | UNE 53526 | - |
| Abrasion (mm3) | UNE 53527 | - |
| Time between coats | 12 hours |
| Start-up time 23ºC | 48 hours |
| Fully cured at 23 ºC | 96 hours |
| Complete curing (industrial application) 160ºC | 12 minutes |
Notas
The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.
PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.
It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.
In the event of a claim, the original packaging must be provided to ensure proper product traceability.
Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.