Traditerm^® Flexible

Technical Caracteristics

Water based product made of binding agents based on acrylic polymers, mineral loads and additives such as  defoamers, preservatives and thickeners.  Free from plasticizers.

Advantages and Uses

• Free from cement.
• Maximum flexibility.
• Great resistance to impacts.
• Waterproof to rainwater
• Permeable to water vapour.
• Ready to use.
• Outdoors and indoors use.

Application Procedure

• With the help of a mixer, stir the product to ensure its homogeneity.
• Minimum 24 hours after placing the reinforcing profiles and after the hollow corners (windows and doors) have been reinforced with MALLA TRADITERM (40x20cm), spread on the insulating panel a layer of TRADITERM FLEXIBLE mortar and comb it afterwards with a notched trowel (8mm).
• Onto the combed r mortar, spread, from up to down, the MALLA TRADITERM, and squash the furrows pressing with the trowel. Cover the mesh with the protruding TRADITERM FLEXIBLE mortar. Even if the mesh is fully covered, the grids should be marked. This layer should have around 1,0-1,5 mm thickness.
• Meshes should be overlapped with a minimum of 10cm.
• Once the layer has gained a certain resistance (3-4 hours after), a new TRADITERM FLEXIBLE mortar layer of 1,0 mm will be applied in order to cover the grids of the mesh and finish the coated surface.
• After 72 hours minimum, we will proceed with the decorative finish, applying FONDO MORCEMCRIL and any of the following claddings afterwards From the morcem range MORCEMCRIL.

Recommendations

• Do not apply the product under 5ºC nor above 35ºC.
• Do not apply the product under risk of frost, rain, heavy winds or direct sun radiation.
• Do not apply it in areas where there might be  any risk of stagnant water.
• Respect the curing timings.
• Ready to use product, do not alter its composition.
• Under low temperatures and high humidity, the drying time may take longer.
• The cleaning of the tools should be done with abundant water immediately after being used.
• It is not advisable to be used as an adhesive for insulating panels.
• Do not apply it on humid surfaces.
• The substrate should be clean, dry and cohesive and without any efflorescenses.
• It is not designed for being coated with plaster.
• Any other use which has not been described in the actual Technical Data sheet will always be carried out under previous enquiry or expressed consent.

Packaging and Storage

26 kg drum. Up to 2 years in its original packaging, properly closed, in fresh and dry places away from inclemency and direct sun. Avoid extreme temperatures (not less than 5°C and not more than 35°C).
 

Technical data

Note : Drying time and yield can be conditioned by specific factors during application or certain characteristics of the support

Yield

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.