2. Products
  3. EIFS/ETICS
  4. Traditerm® Taco de Anclaje STR U 2G

Traditerm® Taco de Anclaje STR U 2G

Traditerm® Taco de Anclaje STR U 2G

Anchor fixings with threaded screw, for fixing TRADITERM® external insulation panels. High quality, secure anchor fixings. As it is a pre-assembled screw, it is easy and quick to install. It ensures a high quality fixing of the insulating panels to the support. With European Certification. Possibility of hidden anchorage in the system. Range of sizes, depending on the thickness of the panel. Use category according to ETA.

Download technical data sheet

Additional information

Technical Caracteristics

Polyethylene anchor fixings with steel screws.

Advantages and Uses

  • Easy and quick to use. Pre-assembled screw.
  • Ensures high quality fastening of insulation panels to the substrate.
  • Anchor fixings with European Certification.
  • Possibility of concealed anchoring in the system.
  • Fixing insulation panels in external thermal insulation system Traditerm®(EWI/ETICS). 
  • ETA usage category: A=Concrete / B=Solid Brick / C=Perforated/Hollow Brick, D =Lightweight Concrete / E=Aerated Concrete.
  • Range of sizes according to thickness of insulation panel.
 

Application Procedure

24 hours after fixing the insulation panels to the substrate with Traditerm® adhesive, drill a hole in the surface of the substrate going through the insulation panel. The drill bit should be 8 mm diameter.

Use the drill in rotary mode, except when the substrate is concrete or solid brick, in which case use it in hammer mode.

There are two methods of installing Traditerm STR U 2G Fixing Anchors:

• Interior Insulation Method.
Place the fixing anchor over the hole and turn towards the inside with the aid of the “Traditerm STR Capping Kit”.
Once the insulation fixing has been inserted, position the corresponding “Traditerm Insulation Cap” according to the insulation type.
 
• Surface Method.
Position the fixing anchor over the drilled hole and turn so that it penetrates the surface of the insulation panel by 1-2 mm.
Next, position the "Traditerm® STR Plug" and level the surface with Traditerm® mortar.
 

Recommendations

  • The fixing should be inserted at least 25 mm into the substrate Categories A, B, C and D and 65 mm inside substrate Category E.
  • The anchor should be cut 1 mm into the insulation panel in the case of the Surface Method. If the anchor is not inserted into the insulation panel, it will be visible in the final finish.
  • Check that the anchors are well secured.
  • The following STR U 2G fixing anchors are recommended, according to the thickness of the insulation panel:
Type of anchorage Thickness of TRADITERM panel (mm) Anchor block length (10 mm thick adhesive mortar layer + 20 mm thick existing plaster layer) Minimum number of anchors / m2 (Typical situations) Approval of anchor plug
Supports type A,B,C y D Supports type E
Traditerm Taco Anclaje STRU 2G  60 115 (surface method only) 115 (surface method only) 6 ETA-04/0023
70 135 175
80 135 175
90 155 195
100 155 195
120 175 215
140 195 235
150 215 255
160 215 255
180 235 275
200 255 295

Packaging and Storage

The fixing anchors are supplied in boxes of 100 units.
Store fixing anchors away from extreme weather conditions and sunlight.

Technical data

(Results obtained in laboratory under standard conditions)

Pre-drill diameter 8 mm
Washer diameter 60 mm
Depth of anchor in substrate 25 mm for substrate Categories A, B, C and D; 65 mm for substrate Category E
Approval  European 
Thermal Conductivity 0.002 W/mK
ETA usage category A=Concrete / B=Solid Brick / C=Perforated/Hollow Brick, D =Lightweight Concrete / E=Aerated Concrete
Performance Minimum 6 units/m2

 

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

 

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.