Pumafix TQV

Technical Caracteristics

Pure resin based vinylester (styrene free).

Advantages and Uses

• Chemical bonding of horizontal and vertical anchors.
• Suitable for wet and dry substrates.
• Indoor and outdoor.
• Suitable for solid and hollow substrates.
• Anchoring machinery
• Anchoring bars, bolts, rods, plates…
• Fixing doors, railings, blinds, awnings, signs, aerials…
• For concrete, stone, brick or hollow concrete substrates.
• For assembling prefabricated concrete elements.
• Excellent mechanical resistance.
• Fast curing.
• Thixotropic, for both vertical and horizontal use.

Suitable Substrates

• Substrates must be resistant, stable, sound and clean, free of dust, demolding agents, organic products, etc. 
• Once the perforation of the substrate has been made, clean any residue using compressed air or a cylindrical brush. 

Application Procedure

INSTRUCTIONS FOR USE INSTALLATION INSTRUCTIONS IN SOLID BRICKWORK FACTORY

• Drill a hole in accordance with the diameter and depth shown on the application table.  During the drilling process, the perpendicularity of the hole in the substrate should be checked. 
• Clean the hole of dust, fragments, oil, water, grease and other contaminants before injecting the mortar (with the manual blower and standard manual brush). 
• The cleaning of the hole consists of 4 blowing operations, 4 brushing operations followed by a further 4 blowing operations. 
• Before brushing, the brush must be cleaned and the diameter checked to ensure it is the correct size.
• The threaded rod must be free from any dust, grease, oil and other impurities.  
• Unscrew the top of the cartridge, engage the mixing nozzle to the cartridge and position in the gun.   
• At the start of using a new cartridge, eject some product until a uniform colour of the mortar appears.  
• Fill the drilled hole uniformly from the bottom up to avoid air pockets, moving the nozzle slowly outwards. 
• Fill 2/3 of the depth of the drilled hole with mortar. 
• Insert the threaded rod slowly and with a slight rotating movement, remove the excess mortar injected from around the threaded rod. 
• Wait the necessary curing time in accordance with the datasheet.
• Do not move or load the anchor until the curing process has finished.  

INSTALLATION INSTRUCTIONS IN HOLLOW/PERFORATED BRICKWORK FACTORY

• Unscrew the top of the cartridge, engage the mixing nozzle to the cartridge and position in the gun.   
• At the start of using a new cartridge, eject some product until a uniform colour of the mortar appears.  
• Fill the drilled hole uniformly from the bottom up to avoid air pockets, moving the nozzle slowly outwards. 
• Fill 2/3 of the depth of the drilled hole with mortar. 
• Insert the threaded rod slowly and with a slight rotating movement, remove the excess mortar injected from around the threaded rod. 
• Wait the necessary curing time in accordance with the datasheet.
• Do not move or load the anchor until the curing process has finished.
• Remove the top of the plastic sieve.
• Introduce the plastic sieve in the hole.
• Fill the sieve uniformly from the bottom up, moving the mixing nozzle slowly towards the outside: move the mixing nozzle 10 mm  towards the outside each time you pull the trigger. 
• Completely fill the sieve.
• Place the top on the filled plastic sieve. 
• Immediately insert the threaded rod slowly and with a slight rotating movement, removing the excess mortar injected from around the threaded rod. 
• Wait the necessary curing time in accordance with the datasheet. 
• Do not move or load the anchor until the curing process has finished.

Recommendations

• Do not use solvents.
• On site use and adjustments to the product are only possible before the hardening of PUMAFIX TQV.
• Store between 5º C and 25º C.
• Consult the Technical Department for any application not specified in this Technical Datasheet.
• For all information regarding safety during handling, transport, storage and use of product please consult the current version of the Product's Safety Sheet.

Packaging and Storage

380 ml 2-component cartridges. (application with special gun) and 280 ml. (application with mono-component product guns).Shelf life: up to 18 months in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)