Morcem^® Dry SF

Technical Caracteristics

High-strength white cement-based product with selected aggregates, special additives and resins.

Advantages and Uses

For waterproofing:

• Small surfaces up to 5-6 m², exposed to negative pressure (up to 1 bar); such as baths, showers, small fountains and wet environments, before tiling.
• Stable substrates.
• Semiflexible mortar compared to traditional mortars.
• Interior use.
• Waterproof.
• Easy to apply.

Suitable Substrates

• Concretes, prefabricated blocks of smooth concrete and renders rich in cement.
• Substrates must be strong, stable, sound and clean, free of dust, residues of mold release agents, organic products, etc.
• If it is hot or windy or if the substrate is very absorbent, it is best to wet the substrate and wait for the film of water to disappear.
• Substrates that are not subject to big movements.

Application Procedure

• Add between 1 and 1.1 litres of water and mix manually or mechanically until the consistency is homogenous and workable.
• With the substrate damp, apply a first thick coat of the product with a flat brush.
• Leave it to dry for about 2 to 4 hours.
• Apply a second coat with the flat brush in the same way.
• It can be finished by smoothing with a trowel or a sponge trowel according to the texture wanted.
• Morcem DRY SF should be applied as evenly as possible, to prevent excess material causing cracks in it.
• Wait at least 4 days before filling with water.

Recommendations

• Do not apply at temperatures below +5ºC or above +30ºC.
• Preferably apply on the positive side, i.e., the one which receives the water pressure.
• If applied on the negative side, there is a risk of it coming away if the water pressure is greater than the adhesion of the material.
• Do not apply where there is risk of frost, rains, strong winds or direct sun.
• To ensure waterproofing, the minimum thickness should be 2 mm.
• In areas where there may be movement like cracks because of retraction of the substrate or critical points of the element to be waterproofed, it is recommended that the covering is reinforced between the two coats with a strip of fine grid mesh, MORCEMDRY MESH [MORCEMDRY MALLA], which should be laid as carefully as possible, avoiding pockets or folds in the mesh. The fiberglass meshes should be bonded with an overlap of a minimum width of 5 cm.
• For wall-wall, wall-floor, wall-ceiling bonding, the application of 5 x 5 cm of Morcemrest RF 15 or Morcemrest RF 35 in the form of beading is recommended.
• Consult the Technical Department for any application not specified in this Technical Datasheet.

Packaging and Storage

5 kg polyethylene bag.
Shelf life: 1 year in its sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)

(A minimum of 2 layers must be applied.In areas with extremely strong filtrations 3 layers must be needed)

CE Mark

GRUPO PUMA SL Avda Agrupación Córdoba 17 14014 Córdoba 21 Nº: 230038
EN-1504-2 MORCEMDRY SF Mortar coating for surface protection, single component semiflexible, minimum layer thickness 2mm.
Capilary absorption and water permeability	≤ 0.1 kg.m2h0.5
Thermal compatibility	Pass
Adhesive strength by tensile test	Pass
Penetration depth	Class I < 10 mm

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.