Morcem^® Grout 500

Advantages and Uses

• Compensated retraction.
• Fluid consistency without segregation or bleeding once mixed.
• High initial and final strength.
• Great self-leveling/filling capacity.
• Once hardened, it is waterproof and impervious to oil, grease and all oil products.
• Free of substances that damage concrete and steel. 
• Excellent adhesion.
• In confined areas provides good adhesion between concrete / steel. Resists knocks and vibrations.
• Leveling supports and bridges.
• Filling by pouring under support plates ensuring perfect load transmission.
• Filling machinery bedplates.
• Filling by pouring or pumping into cracks and holes confined in the inside of concrete masses.
• Filling and anchoring metal profiles (pillars, pipe supports,…) and prefabricated items.
• Anchorages and bolts.

Suitable Substrates

• The substrate should be clean, firm, rough and free of oil, grease, paints, traces of mold release oils, dust, etc.
• The surfaces should be structurally solid.
• The substrate should be wetted to control suction and prevent sudden water loss, but without leaving puddles on the surface.
• It should have a minimum temperature of +5ºC and a maximum temperature of +30 ºC.

Application Procedure

Mixing the mortar:

• Add the product to two thirds of water stipulated. Mix thoroughly adding the remaining water gradually. Do not add more than the recommended amount of water. Mixing can be done manually or mechanically with a mixer at low speed (300 – 600 rpm).

Application:

• After mixing the intended hole can be filled. Avoid taking the mixture any distance before applying it, because moving the mixed mortar may cause decanting. 
• For the filling, it is advisable to pour the material and help it using a rod.
• For filling under plates, an air outlet should be provided, so that air can come out easily during the filling with the product.
• On large surfaces, vibrating with a rod or ramming into place with hardwood tamping tools and mallet is recommended.
• Application layers: between 5 mm and 200 mm (in confined areas layers of up to 500 mm can be achieved).

Curing:

• Once poured, the product should be protected from the sun, wind, etc.
• It is advisable to cover it using wet sacking for 2 or 3 days.
• The curing process is always essential.
• If filling timber or formwork with the product, you should wait 24 hours to release the mold.

NOTE: For large thicknesses applications over 150 mm, it can be mixed with 6-12 aggregate from Triturados Macael (special aggregate) in a proportion of 20%.

Recommendations

• Do not add more water to the mortar than the recommended amount and do not remix.
• Do not apply at temperatures below 5°C or above 30°C.
• Do not add cement, sand or other substances that may affect the properties of the material.

Packaging and Storage

Bags of 25 Kg of powder.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

Statistical data obtained under standard conditions

CE Mark

Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.
Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.