Paviland® Resina Aromática
Polyurethane resin-based binder, for creating decorative surfaces with rubber and aggregate chippings.
Additional information
Features and applications
- For binding rubber panels and flooring in children's play areas and continuous applications installed in-situ.
- For creating surface layers in clear colours it is advisable to use ALIPHATIC RESIN.
Instructions for use
- Before applying the binder, both the substrate or mould, as well as the aggregate or rubber to bind must be completely dry and free from any particles of dust, grease or other contaminating agents.
- The reaction of the AROMATIC RESIN commences with atmospheric humidity or water vapour. The higher the temperature and % of environmental humidity, the faster the reaction time.
FOR APPLYING IN-SITU:
- Pour the AROMATIC RESIN over the aggregate or rubber contained in the recipient used for mixing, homogenised with a low-speed mixer, or else by mixing manually for 2 -3 minutes until the correct consistency has been obtained.
- In order to avoid undesired effects, avoid direct contact with water (rain, intense spraying) during the first 24 hours of curing as this can interfere with the reaction of the product.
LARGE-SCALE APPLICATIONS:
- In order to guarantee top performance and quality for large-scale use, please consult our technical department on the correct temperatures, condition of moulds and type of demoulding agents to be used.
For any sprayed applications please consult our technical department.
Cautions and recommendations
- Apply at least 13% of AROMATIC RESIN to shredded rubber chippings for the base layer. The dosage will vary according to particle size and desired compaction.
- Apply at least 15% of AROMATIC RESIN to shredded rubber chippings for the surface layer. The dosage will vary according to particle size and desired compaction.
- For flooring with thicknesses lower than 22 mm it is essential to apply a primer. Please consult our technical department who will advise you on the best options, according to your requirements.
- For surfaces subjected to heavy foot traffic or strong loads, please consult our technical department on the type of application and maximum thickness per layer.
- Work tools should be cleaned with a solvent immediately after use.
Packaging
In opaque plastic container with net weight of 25 kg.
Store in the original unsealed packaging without between a temperature of 15 - 25ºC in a dry, well-ventilated place. The product has a useful life of 6 months.
Dosage table
The dosage must be previously checked as the porosity or type of aggregate or mineral could require varying percentages. The following table shows the approximate % for creating decorative surfaces (for guidance purposes only).
| DOSAGE | TYPES |
| 3.5 - 4% | For non-porous stones of a diameter of 50 mm or above |
| 4 - 4.5% | For non-porous stones of a diameter between 5 and 50 mm |
| > 4.5% | For non-porous stones of a diameter less than 5 mm |
| 13% | For rubber chips pavements applied in situ (base coat) |
| 15% | For rubber chips pavements applied in situ (finish coat) |
Technical data
| Appearance: | Translucent |
| Density at 25ºC: | 1.061 ± 0.020 g/cm3 |
| Viscosity at 25ºC: | 4400 ± 200 cps |
| Contents in solid particles: | 100% |
| Flash point: | > 200ºC |
| % NCO: | 9.65 ± 0.20 % |
FINISHED PRODUCT CHARACTERISTICS
| TEST | STANDARD | RESULT |
| Stretch to break point (%) | UNE 53510 | - |
| Tensile strength (MPa) | UNE 53510 | - |
| Tear strength (N/mm) | UNE 53510 | - |
| Hardness (Shore A %) | UNE 53130 | - |
| Density (g/cm3) | UNE 53526 | - |
| Abrasion (mm3) | UNE 53527 | - |
| Time between coats | 12 hours |
| Start-up time 23ºC | 48 hours |
| Fully cured at 23 ºC | 96 hours |
| Complete curing (industrial application) 160ºC | 12 minutes |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.