Paviland® Sport AC Acabado

Finely granulated, coloured coating used as an intermediate layer for sport surfaces.

GBC

Download technical data sheet


Additional information

Composition

Acrylic resins in aqueous medium with mineral fillers.

Features and applications

  • Range of colours.
  • Easy application.
  • Solvent-free, water-based product.
  • For indoor and outdoor use.
  • Sports tracks. 
  • Bicycle lanes.
  • Indoor garages and outdoor parking areas for very low-volume traffic.
  • Low-thickness intermediate layer for Paviland Sport AC Systems.
  • Mortar for the finishing of acrylic slurries before being sealed.

Substrates

  • concrete or asphalt of adequate resistance, with open pores and slight roughness.
  • All base materials must be durable, stable, sound and clean free of dust,  release agents (e.g. paint stripper), organic products, etc.
  • Concrete substrates: Prior application of PAVILAND SPORT EPW PRIMER is required (consult the corresponding technical specifications for correct assessment of the concrete), as well as a regularising layer of PAVILAND SPORT AC BASE, which must be dry.
  • Asphalt substrates: prior application of a regularisation layer of PAVILAND SPORT AC BASE is required (consult the corresponding technical specifications for correct assessment of the asphalt base).

Instructions for use

  • This product comes ready for direct application. Must be mixed with an appropriate mixer at low speed for approximately two minutes before its application.
  • Pour the product onto the application surface and spread it with a rubber  squeegee, starting at one corner and continuing linearly end-to-end, taking special care in typical stress points such as joins with vertical walls, etc.
  • Application of a second coat is recommended after approximately 4–6 hours (based on environmental conditions).
  • The total thickness of the product to be applied should be approximately 1 mm.

Cautions and recommendations

  • Do not apply in temperatures below 10°C or above 30ºCDo not apply when there is a risk of frost, rain, strong winds or direct sunlight.
  • Wear protective gloves and goggles during the application. In the event of direct contact with the eyes, wash with plenty of soap and water, and seek the advice of your doctor.
  • In the event of contact with the skin, wash with water before the product dries.
  • Keep out of the reach of children.
  • Clean all the equipment and tools with water immediately after its use. Once the product has hardened it will only be possible to clean such equipment and tools mechanically.
  • Do not eat or smoke during the handling of the product.
  • All empty containers must be discarded in accordance with the current legislation.

Packaging

20 kg containers
The product can be stored for up to one year in its original sealed containers, in a dry and well-ventilated area, at temperatures between 10°C and 30°C, and out of direct sunlight and protected from the elements.

Colour range

Yellow ochre, blue, grey, red and green.

Technical data

(Statistical results obtained under standard conditions).

Appearance Coloured paste
Approximate density  1.5 kg/dm³
Waiting time before accepting pedestrian traffic (*) 4–5 hours
Waiting time before application of the second coat (*) 4–6 hours
Waiting time before application of the sealant layer (*) 4–6 hours
Resistance to abrasion – 8-day Taber test (CS10/1000 g/1000 cycles) 115 mg
Approximate yield 0.4–0.6 kg/m2/layer

(*): These times refer to a temperature of 23°C, and 55% relative humidity. Times are shorter at higher temperatures, and longer at lower temperatures.

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.