Morcemcolor^® Plus Flexible CG2 WA

Technical Caracteristics

Hydrorepelant product based on high resistance cement, high purity aggregates, pigments and additives which hinder the growth of microoganisms.

Advantages and Uses

• AQUASTOP Effect: Repels water creating a "pearl" effect.
• BIOACTIVE Technology: Avoids microbian grouth in wet areas.
• To be applied indoors and outdoors. 
• High resistance to abrasion.
• High hardness.
• Intense colour.
• Easy to clean.
• Very fine texture.
• Low water absorption.
• Cracking resistant.
• Antifungus.
• Antialgae.
• Hydrorepelant.
• Flexible.
• Suitable for underfloor heating systems.

Suitable Substrates

• Empty joints must be dry and clean in all their length and depth.
• Before starting the application, temporary porefiller PROTECMOR protects porous and non-porous ceramic from possible pigment stains.

Application Procedure

• Add water and mix manual or mechanically to a consistent paste (not liquid).
• Let the mixture stand for 5 minutes and remix.
• When working in small areas, grout the joints with a rubber trowel or rechargeable grouting gun, pressing on the paste the material firmly.
• The mixture must be applied diagonally to the joints pressing the mixture onto the joints and removing the excess.
• Let the material dry slightly for 20-30 minutes. When the mixture becomes dull, you can clean the surface with a hard, slightly wet sponge. 
• Polish the surface by using a clean dry cloth to remove dust only when the product has hardened in the joint.
• Let dry for at least 24 hours before normal traffic.
• Use DESMOR to clean up stained tiles. Make sure the product does not damage the tile. Do not use on grouted joints.

Recommendations

• Do not apply below 5ºC nor above 40ºC.
• Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
• Grouting must be carried out at least 24 hours after tile setting on walls or 48 hours after tile setting on floors.
• Do not use in expansion joints or joints subject to structural movements.
• Grout the joints once the floor or cladding is completely dry.
• Do not clean with acids as it may affect application.
• When applied in swimming pools, wait for at least 7 days after the grout has been applied, before filling the pool.
• Joints must be without dust and clean adhesive residue and should have a uniform depth, as at least 2/3 of the total thickness.
• Do not use on stands that are subject to moisture lifts.
• Do not add excess water, since its final performance can reduce.
• Do not clean the ceramic or tile with etching or other acids, since it will affect the color and can reduce the final performance of the Board.
• PH levels suitable for the maintenance of a swimming pool covered between 7 and 8.2, lower pH levels can damage the Board by reducing its durability.
• When dealing with swimming pools, ponds, spa, health resorts, etc. permanent diving conditions in thermal water, sea water or any other surface with saline treatments, it is very important to have an impermeable and acid resistant grouting and therefore, we suggest using MORCEMCOLOR EPOXI.
• In the case of areas subject to frost or very abrupt changes in temperature, it is advisable to MORCEM COLOR epoxy.
• In the case of very absorbant tiles or high temperatures, before refilling the grouting, wet them with clean water, wiping with a wet sponge and avoiding water pooling.
• The amount of water recommended must be respected, since an excess will cause the development of effluorescences on the surface of the grouting.
• Do not clean with an excessive amount of water, or while the product is still fresh, to avoid carbonation and discolouration of the surface due to pigment dispersion.   

Consumption according to dimensions (kg/m²)

Yield (Kg/m²)
Data valid for 6 mm thick tiles

Packaging and Storage

5 Kg polyethylene bags.
Shelf life:
2 years (5 Kg polyethylene bags). In sealed original packaging, sheltered from weather conditions and humidity.

Technical data

Statistical data obtained under standard conditions

Notas

The information and instructions in this datasheet are based on our current tests and technical knowledge. They are intended as general guidance and do not constitute a binding commitment by PIDILITEPUMA MEA CHEMICALS LLC. It is the sole responsibility of the user to verify, prior to use, that the product is suitable for the intended application and to ensure that it is applied correctly and in accordance with applicable regulations and good industry practice.

PIDILITEPUMA MEA CHEMICALS LLC cannot control how its products are applied on site throughout the entire project and therefore cannot accept responsibility for their application by contractors or other parties involved in the execution of the work. Support visits to the jobsite by our technical staff do not change that. Our responsibility is limited exclusively to defects that can be directly attributed to the supplied products, whether used individually or as part of a system, caused by manufacturing defects.

It is the responsibility of the project designer, site manager, contractor, or other relevant professionals to ensure that the selected products are appropriate for the specific project, taking into account their properties, the substrate, site conditions, and any existing issues.

In the event of a claim, the original packaging must be provided to ensure proper product traceability.

Any performance values stated for PIDILITEPUMA MEA CHEMICALS LLC products or construction solutions, whether in UNE standards or other applicable standards, are based solely on the specific test conditions defined in those standards (such as substrate type, temperature, and humidity). These values may not apply to situations where products are tested or used under different conditions.