Adhesivo Carbotec Lámina

Features and applications

• As an adhesive for carbon fiber sheets for structural reinforcement.      
• As an adhesive for steel plate. 
• Excelent adhesion: exceeds the coherence to the substrate.
• Fast curing.
• Filling of fissures / stable cracks/ wihtout movement.      
• Leveling of surface defects such as honeycombs, hollows, etc. 
• For shaping lips of concrete or metal joints without movement,  
• Renovation of edges, mortars and concrete. 
• Adhesive for elastic PVS membrane,  
• High resistance to abrasion and impact.  
• Curing without retraction.
• High resistance
• Easy to mix and apply.
   

Substrates

• The surface to be treated must be clean, desgreased and free from dust in order to obtain an adequate adhesion.  
• On steel surfaces remove surface rust.
• It is recommended the pore of the concrete to be open or create a slight surface roughness to ensure adhesion. 
• It is recommended to apply Implarest EPW when the quality of the concrete is insufficient.
   

Instructions for use

• Stir each component before mixing in order to elimite grounds. 
• Add component B in its totality to component A. This ensures that the volumen ratio between component A and component B is correct. 
• Mix in a low velocity electric mixer (less tan 300 rpm) for about 3 minutes, until  getting a homogeneous gray mixture. 
• Avoid air bubbles.
• Apply Adhesivo Carbotec Lámina with spatula.
• The surface must be clean, dry and free from dust before apliying Adhesivo Carbotec Lámina. 
• It is preferred to apply the adhesive to the Carbotec carbón fiber sheet or steel plate.
• Apply the adhesive in such a way that it is not flat and uniform, but thicker in the center (approx. 5mm) and progressively thinner at the ends (approx. 1 mm). 
• Press the Carbotec carbon fiber sheet or steel plate uniformly over the concrete to spread the adhesive. It is recommended to press with a hard rubber roller, which also removes air bubbles. Clean the excess adhesive before it hardens. 
• Keep the pressure on the carbón fiber until the adhesive has hardened sufficiently. 
• The final thickness of the adhesive coat is 1.5 mm to 2 mm. 
   

Cautions and recommendations

• Mixing and application equipment should be cleaned with solvent.
• Remove hardened material by mechanical means. 
• Consult our Technical Department for any application that might not be specified in this Technical data sheet. 
• For additional information regarding the safe handling, transport, storage and use of the product, please refer to the label and the updated version of the product Safety data sheet.  
   

Consumption according to dimensions (kg/m²)

Consult Lámina Carbotec technical data sheet.

Packaging

5 kg containers.
Keep it in its original packaging in a dry place with temperatures that may go from 5ºC to 30ºC. Once the container is opened, its service life is considerably reduced, so it should be used as soon as possible. Rotate the stored product so that is does not exceed the expiration date (1 year). 
 

Technical data

(*)Typical values after curing for 7 days under a conditioned temperatura of 21ºC. Mechanical properties decrease at temperaturas abouve 50ºC.  

CE Mark

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.