Morcem® Cal Acabado CR CSI W2

Natural hydraulic-lime mortar for coating.Natural composition, highly breathable.


Download technical data sheet

Additional information


Product made with NHL 3.5 lime, selected aggregates and other additives.

Features and applications

  • Highly permeable interior and exterior coating.
  • Highly compatible with traditional systems and so suitable for renovation use.
  • Application on newly built interiors and exteriors for enhanced habitability conditions compared with cement-based mortars.
  • Permeable to water vapour, allowing the substrate to breathe.
  • Excellent adherence.
  • Great plasticity.
  • Smooth or sponge floated finish.
  • Contains no cement.
  • Apply by hand or with a pump.
  • Plaster and stucco works.


  • On surfaces substrates previously treated with MORCEMCAL BASE.
  • The surface should be moistened thoroughly, waiting for the film of water to disappear before applying. 
  • Do not apply on clay or on paint.

Instructions for use


  • Fix the optimum proportion water/mortar according to the chosen pump (section and hose length) and external weather conditions. Start with 18% proportion and modify it gradually until you achieve the appropriate consistency.
  • It is important to maintain the same variables affecting the features of the applied mortar (distance to the wall, angle of application and water proportion).


  • Add water and mix mechanically until it takes on an even and workable consistency.
  • Spread the mixed product over the substrate with the use of a trowel.
  • Spread to a thickness of no more than 0.8 cm.

To assure ensure good compatibility between the surface substrate and the coatings, take the following steps:

  • Wet the surfaces thoroughly at least 24 hours before applying, 
  • Cure the material applied for 24 hours after applying. 
  • Before finishing coatings with MORCEMCAL ACABADO, wait 24–48 hours per centimetre of mortar base coat.

Cautions and recommendations

  • Do not apply at temperatures below 5ºC nor above 30ºC.
  • Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
  • In extreme weather conditions (strong winds or high temperatures) it is necessary to water the product with light sprinklers the day after applying it.
  • The natural origin of the raw materials used in the Morcem Cal mortars, may cause slight changes in color between different production batches.



25 kg plastic paper bags.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)

Aspect Light BEIGE powder
Apparent density of powder 1,85 ± 0,2 g/cm³
Water vapour permeability £ µ6
UNE EN 998-1 Classification CR CSI W2
Approximate yield 16 kg/m² per cm of thickness


Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.
Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.


The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.


Colors in stock

Natural 246
Natural 246
Marengo 325
Marengo 325
Crema 125
Crema 125
Arena 225
Arena 225
Albero 175
Albero 175
Gamuza 425
Gamuza 425
Rojo 333
Rojo 333