MORCEM^® DRY E

Features and applications

• Coating for concrete protection and waterproofing.
• High adhesion to the support.
• Chemical resistance to acids, alkalis and mineral oils.
• Waterproofing.
• Abrasion resistance.
• Coating on concrete or mortar supports such as dams, channels, tanks, decanters.
• Coating of metal elements, in pipes, structures, etc.
• Floor and wall coverings in chambers, laboratories, rooms, halls, warehouses, etc.
• It can be applied outdoors; although it should be noted that it may yellow due to UV effects.
• Suitable for contact with drinking water (EU Regulation 10/2011).

Substrates

• The surface shall be clean of dust, grease and loose particles.
• Sandblasting or pressurized water (200 atm) is recommended, and can sometimes be replaced by a mechanical or manual wire brushing / milling, etc.

Instructions for use

• Begin by stirring the contents of both components separately to homogenize them.
• Pour the entire contents of the container labelled as component B into the container of component A and shake by means of a low speed mechanical shaker (< 600 rpm) for 4-5 minutes, until a product with a homogeneous appearance and color is obtained.
• The mixing ratio of this product is A/B = 84 / 16.
• The product is generally applied by roller or brush.
• IMPLAREST E must be used as a primer.

Cautions and recommendations

• The tools shall be cleaned with the solvent immediately after use.
• Do not apply on recently applied concrete, they should have undergone some curing time.

Resistance to chemicals chart

Note: Change in weight is measured as a %

Imersion test: 1 month at 23ºC

Legend

++ Resist contact

+  Film concerned

-- :Does not resist contact (Film destroyed)e contacto (película destruid

Packaging

Supplied in two-component batches (A+B): 10 Kg

• Component A: 8.4 kg container
• Component B: 1.6 kg container.
• Kits of 10 kg.
• The expiration date is 12 months.

Technical data

CE Mark

GRUPO PUMA S.L Avd. Agrupación Córdoba, Nº 17 14014 (Córdoba)
MORCEM DRY E EN-1504-2 Nº : 230041 Epoxy polymer coating for concrete surface protection and concrete waterproofing.
Direct tensile adhesion	≥ 2.0 Mpa
Water vapor permeability	Class III
Permeability to CO2	Sd > 50m (Class III)
Capilary absorption	≤ 0.1 Kgm-2·h-0.5
Hazardous substances	See Safety Data Sheet
Fire reaction	Class F

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.