Paviland^® Impreso

Technical Caracteristics

Product based on high strength Portland cement, selected aggregates, pigments, and great purity additives.

Advantages and Uses

• Suitable for application over a wide temperature range.
• Allows the floor to be cleaned using high-pressure water at an early age, even under cold weather conditions.
• Pedestrian walkways in parks and landscaped areas.
• Great workability.
• Public squares.
• Streets, pavements, external areas, residential access roads, swimming pool surrounds and urban roads subject to pedestrian and vehicle traffic.
• High mechanical strength at early, intermediate, and long-term ages.
• Outdoor sports facilities.
• Car parks.
• High resistance to abrasion.
• Wide range of textures and colours.
• Different stamped patterns and colour combinations can be achieved simply by changing the mould and the selected colour.
• No changes in outdoors substrates.

Application Procedure

• ​​​​​Prepare the substrate by placing the appropriate reinforcement before casting the concrete.
• Protect all adjacent areas that must remain clean.
• Pour the concrete and smooth it with a trowel. Do not vibrate it.
• Spread PAVILAND IMPRESO evenly over the fresh concrete surface, ensuring a uniform distribution of colour and avoiding excessive build-up or areas with insufficient material.
• Finish the surface using a telescopic trowel. Apply additional PAVILAND IMPRESO where necessary to achieve complete and uniform coverage, then trowel it again.
• Ensure that the product is fully hydrated using only the mixing water contained in the fresh concrete. Do not add extra water, as this will significantly reduce the mechanical resistances.
• Apply PAVILAND DESMOLDEANTE release agent before placing the stamping moulds onto the concrete while it remains in its plastic state.
• Press the moulds evenly to obtain a uniform imprint across the entire surface.
• After approximately 48 hours, remove the release agent using a high-pressure water jet. Under cold weather conditions, this operation may be delayed for up to 72 hours.
• The surface layer shall be protected against rapid drying to prevent premature moisture loss from the mortar, particularly under conditions of elevated temperature and/or intense winds.
• For this, the use of PAVILAND RESINA curing and/or protective resins is recommended.

Recommendations

• Do not apply the product under temperatures of 5º nor above 30º.
• Do not apply if there is risk of frost, rain, heavy wind, or direct sun light.
• Use gloves and protective goggles when manipulating the product.
• The application of a PAVILAND RESINA curing resin is required after installation, as described in the Application Instructions. (Application using a low-pressure pump is recommended).
• It is necessary to have membranes, plastic sheets, or vapour barriers in place before pouring the concrete to provide an impermeable element that prevents moisture rising from the ground into the pavement.

Packaging and Storage

25 Kg of plastic laminated paper bags.
Store up to 1 year in its original closed container, away from extreme weather conditions and humidity.

Technical data

(Statistic results obtained under standard conditions)

(*) Consumption may vary depending on the selected colour, the colour of the concrete substrate and the type of stamping pattern used. Please consult our technical department for white colour.

CE Mark

GRUPO PUMA ESPAÑA, S.L  Avda. AGRUPACIÓN CÓRDOBA, Núm. 14014 CÓRDOBA 26
PAVILAND IMPRESO Nº: 500087-01 EN 13813 CT-C40-F5-A15 dry surface hardener which, when applied on fresh concrete, forms a monolithic wearing layer with extremely high abrasion resistance and high early mechanical strength.
Reaction to fire	A1 Class
Hazardous substances emission	CT
Compressive Strength	C40
Flexural strength	F5
Abrasion resistance	A15
Hazardous substances	Consult safety data sheet

Environmental Product Declaration (EPD)

Mortar made with aggregates close to the production centres, reducing greenhouse gas emissions associated with its transport and made in production centres with Environmental Management systems certified in accordance with the ISO 14001 standard, a firm commitment to sustainability and respect for the environment. Mortar with type III ecological label (the most demanding) Environmental Product Declaration externally verified by AENOR.

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.