Paviland® Sport EPW Acabado
Finely granulated, coloured, two-part acrylic-epoxy coating that acts as an intermediate or finishing layer on sports floors subject to a significant degree of mechanical wear.
Additional information
Composition
Acrylic-epoxy resins in aqueous medium with mineral fillers.
Features and applications
- Range of colours.
- Easy application.
- Water-based product.
- Indoor and outdoor use.
- Continuous-use sports floors.
- High-durability bicycle lanes.
- Indoor garages and outdoor parking areas for very low-volume traffic.
- Fine, intermediate layer for PAVILAND SPORT EPW Systems.
- Resistant to oil spills.
Substrates
- All base materials must be durable, stable, sound and clean, in addition to being free of dust, form release agents (e.g. paint stripper), organic products, etc.
- Concrete bases: prior application of PAVILAND SPORT EPW PRIMER is required (consult the corresponding technical specifications for correct assessment of the concrete).
- Asphalt bases: prior application of a regularisation layer of PAVILAND SPORT AC BASE is required (consult the corresponding technical specifications for correct assessment of the asphalt base).
Instructions for use
- Mix the separate A and B components.
- Add all of component B to component A and mix both components with an appropriate mixer at low speed until a uniform consistency has been obtained.
- Empty the product onto the base and spread with a rubber strip, starting at one corner and continuing in a line from end-to-end, taking special care at special points such as joins with vertical walls, etc.
- The second coat should be applied after approximately 2 hours, provided that the first coat is completely dry.
Cautions and recommendations
- Do not apply in temperatures below 10°C or above 30°C.
- Do not apply when there is a risk of frost, rain, strong winds or direct sunlight.
- Wear protective gloves and goggles during application. In the event of direct contact with the eyes, wash with plenty of soap and water, and seek the advice of your doctor.
- In the event of contact with the skin, wash with water before the product dries.
- Keep out of the reach of children.
- Remember to clean all equipment and tools with water immediately after use. Once the product has hardened, it will only be possible to clean such equipment and tools mechanically.
- Do not eat or smoke during handling.
- All empty containers must be discarded in accordance with current legislation.
Packaging
Containers of 20 (19 + 1) kg.
The product can be stored for up to one year in its original sealed containers, in a dry and well-ventilated area, at temperatures between 10°C and 30°C, and out of direct sunlight and protected from the elements.
Colour range
Yellow ochre, blue, grey, red and green.
Technical data
(Statistical results obtained under standard conditions).
| Appearance | A: white paste – B: coloured paste |
| Approximate density of the mixture | 1.4 kg/dm3 |
| Ratio of the mixture (A: B) | 95 : 5 |
| Active lifetime of the mixture (*) | 90 minutes |
| Wait time before application of the second coat (*) | 2 hours |
| Wait time before application of the sealant layer (*) | 2 hours |
| Resistance to abrasion | 90 mg |
| Slip resistance according to the Technical Building Code (CTE) | > 45 (class 3) |
| Approximate yield | 0.5 kg/m2/layer |
(*): These times refer to a temperature of 23°C, and 55% relative humidity. Times are shorter at higher temperatures, and longer at lower temperatures.
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.