Pegoland® Fast Fluido C2 FE

Fast hardening cement adhesive in fluid format, for indoor and outdoor floor tiling jobs, specially recommended for large areas and for floors with underfloor heating systems. Suitable for bonding all types of ceramic tiles.fIt has a fast curing and excellent bonding.

12004 - C2 FE COV DAP Casita_SueloIntExt

Download technical data sheet

Additional information


Product based on high resistance cement, selected aggregates, additives and synthetic resins which give fast curing and provide excellent bonding.

Features and applications

  • For applying on indoor and outdoor flooring.
  • Suitable for all types of ceramic tiles. Highly recommended for large format tiles.
  • No need to wet tiles or substrates thanks to its high water-retaining capacity.
  • Excellent initial adherence.
  • Superb adherence and correct setting with low-porosity materials such as porcelain stoneware.
  • To tile large areas with intense traffic and floors with underfloor heating.
  • Rapid setting.
  • Fluid product with optimum water-retaining capacity.


  • Conventional cement-based substrates.
  • Ceramic flooring.
  • Floor coverings such as marble, granite, terrazzo, natural stone and all types of tiles.
  • Substrates must be resistant, stable, sound and clean, free of dust, demolding agents, organic products, etc.
  • All substrates must have the appropriate flatness. Otherwise, smooth down up to 5 mm with the same product 48 hours prior to bonding.
  • In case of greater thickness should be used:
    • On floors: Depending on the particular need use 10R NIVELAND 10 R or PAVILAND RECRECIDO AUTONIVELANTE.
    • On walls: mortars with adequate tensile strength with drying shrinkage already completed.
  • In case of hot or windy weather conditions or when applying over absorbent substrates, it is advisable to wet the substrate and wait till the thin layer of water disappears.
  • Do not apply on clay, paint or on elements prone to disintegrate.
  • On outdoor flooring, substrates must have a gradient equal or superior to 1%.

Instructions for use

  • Add water and mix by hand or mechanically until it takes on an even and workable consistency (6.5 to 7 litres per bag).
  • Let the mixture stand for 2 minutes and remix.
  • Spread the mixed product on the substrate with a trowel to a maximum surface area of 2m2.
  • Spread with a notched trowel to adjust thickness (see chart).
  • Place the pieces on the fresh adhesive, pressing and moving until the grooves are completely crushed and the entire surface of the ceramic is properly adhered, periodically check the stickiness of the adhesive by lifting a previously laid tile, if a non-transfer film appears on the surface of the adhesive, or dehydration of the adhesive, proceed to remove the material and apply a new product.
  • Observe construction joints (expansion, contraction, fraction, perimeter corner joints) and the joints between the cement slabs (minimum of 2 mm inside and 5 mm outside).
  • After 8 hours, use the appropriate mortar from the MORCEMCOLOR range depending on the type of joint.

NOTE: For better results lay tiles as soon as possible after spreading.

Notched-trowel panel

< 1.600 cm2 U9 (9 x 9 x 9) Simple
> 1.600 cm2 n10 Simple

Cautions and recommendations

  • Do not apply below 5ºC nor above 30ºC.
  • Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
  • Do not apply in areas where water may accumulate.
  • Under extreme weather conditions (gusty winds or high temperatures) drying may occur faster.
  • On floor coverings and facings with a surface area greater than 50 m2  for interiors and 30 m2  for exteriors, or for elongated areas over 15 lineal metres it is recommended to leave separation or sealing joints filled with a deformable material (PUMALASTIC range of products).
  • In case of Indoor floor tiled areas larger it is recommended to leave a free perimeter joint between the tiles and the wall or pillar of about 5 mm hidden by the plinth. These joints must be filled with a deformable grout among PUMALASTIC range.
  • On floorings with underfloor heating, apply when substrate is at room temperature (between 5ºC and 30ºC).
  • On floorings with underfloor heating, this should be switched off at least 48 hours prior to use and should be switched back on again gradually after at least 7 days of installing the flooring and pointing operation.
  • In case of tiles reinforced with fiberglass mesh on their back, ask the technical department.
  • Do not use the technique known as by globs.
  • Working and setting times of the adhesive depend on the temperature, air streams, and the absorption of tiles and substrates. 
  • On ceramic pavements (overlays), remove the badly adhered pieces and fill the gaps with mortar the day before the application of the new tiling. Ensure that the old ceramic is free of traces of fats or waxes, if necessary proceed to the milling of the enameled surface until the loss of brightness of the old ceramic. In case of doubt, make a preliminary test to establish the suitability of the solution provided.


25 kg plastic-lined paper bags
Shelf life: 6 months in sealed original packaging, sheltered from weather conditions and humidity.

Technical data

(Statistical data obtained under standard conditions)

Aspect  GREY powder
Adjustment time Approx. Approx. 30 min. (depending on weather conditions)
Paste shelf life Approx. Approx. 1 hour (depending on weather conditions)
Waiting time before usage 8 hours after the start of setting
Setting time at 23ºC±2ºC Approx. 2 hours 30 minutes (depending on weather conditions)
Adherence after 6 hours ≥ 0,5 N/mm2
Initial tensile adhesion strenght ≥ 1 N/mm2
Tensile adhesion strenght after water inmersion ≥ 1 N/mm2
Tensile adhesion strenght after heat ageing ≥ 1 N/mm2
Tensile adhesion strenght after freeze-thaw cycles ≥ 1 N/mm2
Service temperature -30ºC a 90ºC
UNE-EN 12004 Classification C2 FE
Approximate yield 4 Kg/m2


Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment.
Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.


The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.