Pumaplast Renovación Extra

Advantages and Uses

• For application on painted interior surfaces, to smooth and level walls with textured paint, gotelé, or other relief finishes.
• Suitable for covering satin or shiny paints and for smoothing and levelling walls after removing wallpaper or carpet.
• Do not paint the surface before checking the putty applied.
• Before applying any paint or any other decorative technique, ensure that the applied putty is completely dry. It is recommended that the surface be clean and free of dust.
• As a general rule, a primer should be applied before painting, texturing, or wallpapering to equalize the absorption capacity of the entire surface.
• Proper ventilation of the area, promoting air circulation, minimizes issues caused by humidity. In case of high humidity levels, the use of dehumidifiers may be necessary.
• The manufacturer's instructions for the decorative material used must be carefully followed.
• The manufacturer's instructions for the paint or decorative material, as well as those specified by the painter for these types of substrates, should be followed. This is in accordance with Royal Decree 615/2013 of August 2, which establishes the professional certification for the occupation of painter.

Suitable Substrates

• Substrates must be consistent.
• Powdery substrates must be consolidated with a fixer, as dust prevents proper adhesion between materials. Similarly, old substrates made of degraded gypsum or poorly adhered sections must be repaired, as restoring surfaces without prior treatment is not advisable. Additionally, the substrate must be free from any traces of salty residue, fungi, micro-organisms, dust, grease, or any material that could hinder proper adhesion of the product.
• In case of traces of fungi, algae, or other microorganisms, the surface should be treated beforehand. If dealing with efflorescence, treat with an acidic dilution.

Application Procedure

• If there are cracks or deep imperfections on the surface to be treated, it is recommended to fill and repair the substrate.
• If the surface to be covered has a wax finish, it is recommended to apply a primer before the putty to ensure good adhesion. Optimal ventilation conditions must be maintained for a proper drying process.
• Sprinkle the product over water, let it rest for 3 to 5 minutes, then mix with a mechanical mixer until a homogeneous, dense, and lump-free paste is obtained.
• Once mixed, proceed with application. The approximate working time will be between 3-4 hours, depending on mixing conditions and usage.
• No additives should be added on-site, as this could alter the setting process and the final strength of the product.
• Once the paste has been mixed, do not add water.
• Tools should be cleaned before each mixing. Use clean water for preparation.
•  Apply at a temperature between 5°C and 35°C. Excessively high temperatures may cause adhesion issues due to rapid water evaporation, while cold and excessively humid environments may also negatively impact adhesion.
   

Recommendations

• Please follow the instructions given on the corresponding data sheet at all times.
• Do not add additives or any other paste-based product to the putty, as this may alter its properties.
• Do not apply on walls subjected to permanent humidity.
• The application temperature must not be below 5ºC or above 35ºC.
• The product should not be applied when there is a risk of frost.
• It is recommended that the application area has proper ventilation to prevent excessive humidity.
• For detailed safety information, refer to the product's safety data sheet.

Packaging and Storage

This product is sold in double-layer paper sacks with a plastic liner, containing 15 kg. ± 5% and on pallets of 72 sacks.

Store the product in a dry, covered place, protected from frost and direct sunlight. Keep it elevated from the ground to protect it from moisture.
PUMAPLAST RENOVACIÓN EXTRA has a shelf life of 12 months from the date of manufacture, provided it is stored in its original, sealed, and undamaged packaging under the recommended conditions. Humidity, extreme cold, or heat can accelerate its ageing, potentially altering the putty's performance.

Technical data

Note: The working or application times may vary depending on the water-to-powder ratio, temperature, pH of the water, type of substrate, mixing time, and speed.

Legal Disclaimer

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.