43 products in total
Class R4 mono - component high performance repair mortar suitable for large thicknesses. Formulated with sulphate resisting cement.
High resistance monocomponent R4 repair mortar for large thicknesses.
R4 high resistance mono-component mortar for thick applications.
Formulated with Sulfo-resistant cement, selected aggregates and additives; reinforced with fibres.
Self-compacting high-resistance fluid mortar and balanced retraction.
Thixotropic mortar of high strength, with fiber for concrete repair and protection , based on nano-silane technology . Classification R4
Dry mortar. Designed for usual and ordinary masonry applications in which a rapid and high performance mortar is required.
Rapid setting cement prepared. To block water leaks in concrete cracks or fissures on other base-cement surfaces.
Adhesivo Carbotec Lamina is an epoxy resin. Bi-component resin and free from solvents. It has great adhesion to all types of substrates, even without primer and high resistance to abrasion.
A set of unidirectional carbon fibre yarns of high mechanical resistance, housed inside a cotton thread net that gives them a "rope" appearance. Once stiffened with epoxy adhesive, they are used to anchor and structurally connect CARBOTEC systems or other types of structural reinforcement systems to the foundation to be reinforced.
Carbotec sheets are manufactured through a pultrusion process from carbon fibre filaments arranged in an epoxy resin matrix. There are three different types of sheets: with an elasticity of 170 GPa module (Most commonly used: low modules: LM), of 200 GPa (high module: HM) and 250 GPa (of very high module, for specific applications: UHM).
The Tejido Carbotec System is composed of a unidirectional carbon fiber fabric wrapped in a weft of glass thread covered with thermoplastic material that allows to maintain the position of the carbon fibres during its implementation. It is supplied in rolls of different widths and lengths.
Carbotec impregnante adhesive is a resin which, due to its impregnation and thixotropy allows the adherence of the carbotec tissue on concrete elements, reinforced concrete or brickwork.
Renovation mortar for the treatment of damp by capillarity on the lower parts of the wall, facilitating the evaporation of water retained in the wall.
High-strength mortar for filling and anchorage of machinery, leveling supports and bridges, etc.Medium and thick layers.
High-strength mortar with self-leveling controlled expansion and no retraction.Medium and thick layers.
High-conductivity grout for pumping, injecting and filling in geothermal plant heat exchangers.
MORCEM ELASTIC PM TRANSPARENTE, is a transparent and aliphatic polyurethane resin that, once cured, creates a continuous, elastic membrane, without joints or overlaps, totally watertight and waterproof.
It can be applied by brush or roller.
Single-component polyurethane membrane that produces a continuous, elastic, aromatic membrane completely adhered to the substrate, watertight and 100% waterproof. Its properties make it excellent for its application on all types of surfaces, whether in new construction or rehabilitation. It has the CE stamp based on a Declaration of Presentations (DoP) made according to the UE305/211 regulation. The MORCEM ELASTIC PM membrane has an ETE 20/0439 certification, with 25 years of useful life for a minimum thickness of 1.5 mm.
One-component, fibre-reinforced, fast-hardening and drying, waterproofing membrane, endowed with high flexibility and extended open time, for waterproofing and adhesion of tiles on traditional substrates.
Bicomponent, solvent-free epoxy resin coating. It can be applied on substrates in contact with aqueous foods or drinking water. Provides waterproof coatings with high resistance to abrasion and acids and alkalis.
MORCEMDRY PU UV Varnish is a bi-component aliphatic polyurethane elastic render with solvent.
It provides UV resistant, elastic, protective films with high resistance to industrial, polluting atmospheres
Reinforcement mesh for the assembly of the MORCEM ELASTIC PM waterproofing membrane in areas or points described in this document.
Impermeable mortar of two-components additives for the execution of impermeable coatings.
MORCEMDRY PU UV Varnish is an elastic two-component aliphatic polyurethane coating with solvents. It provides resistant and elastic protective films against ultraviolet rays. In addition to that, these films are elastic and also offer great resistance against industrial environments and other pollutants.
Anti-rust primer on metallic substrates, by forming an electronic barrier of cathodic protection.
Two-component water-based epoxy primer/ bonding bridge for preparing damp and dry surfaces.
Corrosion protection for steel reinforcements from the Morcemrest restoration system, in compliance with EN 1504-7. This product can be combined with other repair mortars from the Morcemrest range. Cementitious anti-corrosion mono-component primer, modified with polymers for protecting reinforcement. When mixed with water a grout is obtained which is applied to the previously cleaned steel. Due to its high pH level Implarest C creates a passivation layer on the surface of the reinforcement, halting the corrosion process. Implarest C is a corrosion protector classified in compliance with EN 1504-7.
Epoxy 100% solid, two-component adhesive, specially formulated for bonding new and old concrete. Once mixed a semi-fluid liquid is obtained which may be applied above 10ºC. It can be used as protection barrier of the steel of the reinforced concrete. It will be applied on the clean reinforcement.
Implarest PU is a two-component semi-elastic cladding of polyurethane free from solvents. It prepares the surface for the application of water repellent claddings of great thickness and great resistance to abrasion.
Low viscosity two-component epoxy resin for injections in concrete.
Transverse butyl deformable cold adhesive strip, composed of a visco-elastic layer covered by a non-woven fabric, resistant to alkalis. Theupport allows adaptation to the shape of the substrate and is highly recommended for specific applications of MORCEM® ELASTIC PM liquid polyurethane, and for elastic cementitious waterproofing systems.
Waterproof coating with high elasticity based on an aqueous dispersion of self-crosslinking acrylic resins by UV rays, suitable for protection and decoration of all kind of material façades (concrete, cement, brick, etc.) giving the support an excellent resistance to the most thus obtaining a top quality finish and in which contractions of the facing are foreseen that may cause cracks.
Preserves concrete structures from degradation caused by atmospheric agents as well as façades, precast elements, beams, pillars, etc.
Two-component thixotropic epoxy adhesive; like multipurpose adhesive for most construction materials; suitable for filling joints, cracks and small holes.
Product indicated for the regularisation of vertical surfaces with plastic or paint coatings (except for silicates or polyurethanes), concrete, stuccoed walls or mortar or ceramic plastering.
Fast-setting binder. Designed as a setting and hardening regulator for making fast-setting mortars with high strength and dimensional stability.
Injection resin for anchorage, 2-component and fast curing, resin-based polyester. Styrene-free. Multifunctional, for solid or hollow substrates.
High-performance, one-component, neutral and elastic filler for sealing and bonding.
Morcem®Dry Mesh consists of double weave threads, essential for the reinforcing.
Recommended in the application of swimming pool waterproofing systems as DryPool. Gives the system great resistance and stability, and prevents the appearance of cracks caused by temperature differences or movements.